FPGA-任务五、十字路口交通控制灯器系统设计（二）
生活随笔
收集整理的這篇文章主要介紹了
FPGA-任务五、十字路口交通控制灯器系统设计（二）
小編覺得挺不錯的,現在分享給大家,幫大家做個參考.
完整功能：
實現主干道和支干道的紅綠燈，并實現時間顯示功能；（前兩位顯示東西的 ? ? 后兩位顯示南北的）
實現綠燈，黃燈，紅燈的持續時間固定的交通控制功能；
（狀態機切換三段的顯示 ）
當東西或南北兩路中任一道上出現特殊情況，交通控制系統應可由交警手動控制立即進入特殊運行狀態的功能；（控制一個SW[0]----> ?en 計數器計數半秒使能半秒）
實現綠燈，黃燈，紅燈的持續時間可調的交通控制功能
（按鍵key_up 控制加 ?按鍵key_down 控制減）；
?
top.v改變?yōu)?#xff1a;
module top(ext_clk_25m,ext_rst_n,switch1,switch2,key_upup,key_down,key_entr,dtube_cs_n,dtube_data,led);
//頂層控制模塊input ext_clk_25m; //時鐘信號25MHzinput ext_rst_n; //復位信號input switch1;input switch2; input key_upup;input key_entr;input key_down;output [3:0] dtube_cs_n; //段選數據位output [6:0] dtube_data;//位選數據位output [7:0] led;wire [3:0] TimeL;wire [3:0] TimeH;wire [3:0] TimeL1;wire [3:0] TimeH1;wire [7:0] red;wire [7:0] green;wire [7:0] yellow;wire [3:0] timesh;wire [3:0] timesl;wire en1;wire en2;wire set_en;wire clk;//中間變量//控制電路模塊control con1(.ext_clk_25m(ext_clk_25m),.ext_rst_n(ext_rst_n),.switch1(switch1),.switch2(switch2),.en1(en1),.en2(en2),.set_en(set_en));//設置時間模塊set set1(.ext_clk_25m(ext_clk_25m),.ext_rst_n(ext_rst_n),.set_en(set_en),.key_upup(key_upup),.key_down(key_down),.key_entr(key_entr),.red(red),.yellow(yellow),.green(green),.led(led[7:6]),.times1(timesh),.times2(timesl));//分頻25MHZ變?yōu)?HZdiv d1(.ext_clk_25m(ext_clk_25m),.ext_rst_n(ext_rst_n),.mclk(clk));//倒計時計數模塊(東西)counter c1(.ext_clk_25m(ext_clk_25m),.mclk(clk),.ext_rst_n(ext_rst_n),.cnt_en(en2),.set_en(set_en),.red(red),.green(green),.yellow(yellow),.TimeH(TimeH),.TimeL(TimeL),.led(led[2:0]));//倒計時計數模塊(南北)counter1 c2(.ext_clk_25m(ext_clk_25m),.mclk(clk),.ext_rst_n(ext_rst_n),.cnt_en(en2),.set_en(set_en),.red(red),.green(green),.yellow(yellow),.TimeH1(TimeH1),.TimeL1(TimeL1),.led(led[5:3]));//數碼管顯示模塊(東西,南北)seg s1(.ext_clk_25m(ext_clk_25m), .ext_rst_n(ext_rst_n), .seg_en(en1),.set_en(set_en),.set_segh(timesh),.set_segl(timesl),.TimeH(TimeH),.TimeL(TimeL),.TimeH1(TimeH1),.TimeL1(TimeL1),.dtube_cs_n(dtube_cs_n), .dtube_data(dtube_data) );
endmodule?
控制電路模塊：
module control(ext_clk_25m,ext_rst_n,switch1,switch2,en1,en2,set_en);input ext_clk_25m; //輸入時鐘input ext_rst_n ; //復位信號input switch1 ; //特殊狀態開關input switch2 ; //設置狀態開關output reg en1 ; //數碼管使能位output reg en2 ; //交通燈使能位output reg set_en ; //設置使能位reg [24:0] cnt ; //存放計數器的值parameter TIME = 25'd2500_0000;//數碼管特殊狀態閃爍計數器模塊always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)begincnt <=25'd0;endelse if(cnt ==TIME-1'b1)begincnt <=1'b0;endelse begincnt <=cnt + 1'b1;endend//開關控制設置的開啟always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginset_en <=1'b0;endelse if(switch2==1'b0)beginset_en <=1'b1;endelse beginset_en <=1'b0;endend//數碼管閃爍模塊always @(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginen1<=1'b0;endelse if(switch1==1'b0)beginif(cnt<(TIME/2-1'b1))beginen1<=1'b1;endelse beginen1<=1'b0;endendelse beginen1<=1'b0;endend//停止計數器計時模塊always @(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginen2<=1'b0;endelse if(switch1==1'b0)beginen2<=1'b1;endelse beginen2<=1'b0;endendendmodule分頻模塊：
module div(ext_clk_25m,ext_rst_n,mclk);input ext_clk_25m ;//輸入時鐘input ext_rst_n ;//復位端口output reg mclk ;//輸出1Hzreg [23:0] cnt ;//存放計數器的值parameter TIME= 24'd1250_0000;//時鐘25MHz
//分頻模塊,使得輸入時鐘為25MHz輸出時鐘為1Hzalways@ (posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)beginmclk <=1'b0;cnt <=24'd0;endelse if(cnt ==TIME-1'b1)beginmclk <=~mclk;cnt <=1'b0;endelse begincnt <=cnt + 1'b1;endend
endmodulecounter.v
module counter(ext_clk_25m,mclk,ext_rst_n,cnt_en,set_en,red,green,yellow,TimeH,TimeL,led);input ext_clk_25m ;//系統時鐘input mclk ;//時鐘信號input ext_rst_n ;//復位信號input cnt_en ;input set_en ;input [7:0] red ;input [7:0] green ;input [7:0] yellow ;output reg[3:0] TimeH ;//兩位數碼管顯示高位output reg[3:0] TimeL ;//兩位數碼管顯示低位output reg[2:0] led ;//led指示狀態reg [2:0] state_c ;reg [2:0] state_n ;reg [7:0] times;parameter [2:0] IDLE = 3'b001,S1 = 3'b010,S2 = 3'b100;//狀態機實現三種狀態切換模塊always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)beginstate_c <=IDLE;endelse if(set_en==1'b1)beginstate_c <= IDLE;endelse if(cnt_en==1'b1)beginstate_c <= state_c;endelse beginstate_c <= state_n;endend//狀態切換always@(*)begincase(state_c)IDLE:beginif({TimeH,TimeL}==8'h01)beginstate_n=S1;endelse beginstate_n=IDLE;endendS1:beginif({TimeH,TimeL}==8'h01)beginstate_n=S2;endelse beginstate_n=S1;endendS2:beginif({TimeH,TimeL}==8'h01)beginstate_n=IDLE;endelse beginstate_n=S2;endenddefault:state_n=state_c;endcaseend always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)begintimes <=8'd00;endelse if(set_en==1'b1)begintimes <=8'd00;endelse if(state_c==IDLE)begintimes <=red;endelse if(state_c==S1)begintimes <=green;endelse if(state_c==S2)begintimes <=yellow;endelse ;endalways@(posedge mclk or negedge ext_rst_n)beginif(!ext_rst_n)beginled <=3'b111;endelse if(state_c==IDLE)beginled<=3'b110;endelse if(state_c==S1)beginled<=3'b101;endelse if(state_c==S2)beginled<=3'b011;endelse beginled<=3'b111;endend
//計數器模塊高位always@(posedge mclk or negedge ext_rst_n)beginif(!ext_rst_n)beginTimeH <=times[7:4]; //計數器賦初值endelse if(set_en==1'b1)beginTimeH <=times[7:4];endelse if(cnt_en==1'b1)beginTimeH <=TimeH;endelse if({TimeH,TimeL}==8'h00)beginTimeH <=times[7:4]; endelse if(TimeL==4'h0)beginTimeH <=TimeH-1'b1;endelse beginTimeH <=TimeH;endend//計數器模塊低位always@(posedge mclk or negedge ext_rst_n)beginif(!ext_rst_n)beginTimeL <=times[3:0];endelse if(set_en==1'b1)beginTimeL <=times[3:0];endelse if(cnt_en==1'b1)beginTimeL <=TimeL;endelse if({TimeH,TimeL}==8'h00) beginTimeL <=times[3:0];endelse if(TimeL==4'h0)beginTimeL <=4'h9;endelse beginTimeL <=TimeL-1'b1;endend
endmodulecounter1.v
module counter1(ext_clk_25m,mclk,ext_rst_n,cnt_en,set_en,red,green,yellow,TimeH1,TimeL1,led);input ext_clk_25m ;//系統時鐘input mclk ;//時鐘信號input ext_rst_n ;//復位信號input cnt_en ;//使能信號input set_en ;input [7:0] red ;input [7:0] green ;input [7:0] yellow ;output reg[3:0] TimeH1 ;//兩位數碼管顯示高位output reg[3:0] TimeL1 ;//兩位數碼管顯示低位output reg[5:3] led ;reg [2:0] state_c ;reg [2:0] state_n ;reg [7:0] times1 ;parameter [2:0] IDLE = 3'b001,S1 = 3'b010,S2 = 3'b100;//狀態切換模塊always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)beginstate_c <=IDLE;endelse if(set_en==1'b1)beginstate_c <=IDLE;endelse if(cnt_en==1'b1)beginstate_c <= state_c;endelse beginstate_c <= state_n;endend//狀態切換always@(*)begincase(state_c)IDLE:beginif({TimeH1,TimeL1}==8'h01)beginstate_n=S1;endelse beginstate_n=IDLE;endendS1:beginif({TimeH1,TimeL1}==8'h01)beginstate_n=S2;endelse beginstate_n=S1;endendS2:beginif({TimeH1,TimeL1}==8'h01)beginstate_n=IDLE;endelse beginstate_n=S2;endenddefault:state_n=state_c;endcaseend always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)begintimes1 <=8'd00;endelse if(set_en==1'b1)begintimes1 <=8'd00;endelse if(state_c==IDLE)begintimes1 <=green;endelse if(state_c==S1)begintimes1 <=yellow;endelse if(state_c==S2)begintimes1 <=red;endelse ;endalways@(posedge mclk or negedge ext_rst_n)beginif(!ext_rst_n)beginled <=3'b111;endelse if(state_c==IDLE)beginled<=3'b101;endelse if(state_c==S1)beginled<=3'b011;endelse if(state_c==S2)beginled<=3'b110;endelse beginled<=3'b111;endend//計數器模塊高位always@(posedge mclk or negedge ext_rst_n)beginif(!ext_rst_n)beginTimeH1 <=times1[7:4]; //計數器賦初值endelse if(set_en==1'b1)beginTimeH1<=TimeH1;endelse if(cnt_en==1'b1)beginTimeH1<=TimeH1;endelse if({TimeH1,TimeL1}==8'h00)beginTimeH1 <=times1[7:4]; //計數器賦初值endelse if(TimeL1==4'h0)beginTimeH1 <=TimeH1-1'b1;endelse beginTimeH1 <=TimeH1;endend//計數器模塊低位always@(posedge mclk or negedge ext_rst_n)beginif(!ext_rst_n)beginTimeL1 <=times1[3:0];endelse if(set_en==1'b1)beginTimeL1 <=times1[3:0];endelse if(cnt_en==1'b1)beginTimeL1 <=TimeL1;endelse if({TimeH1,TimeL1}==8'h00)beginTimeL1 <=times1[3:0];endelse if(TimeL1==4'h0)beginTimeL1 <=4'h9;endelse beginTimeL1 <=TimeL1-1'b1;endend
endmoduleseg.v
module seg(ext_clk_25m,ext_rst_n,seg_en,set_en,set_segh,set_segl,TimeH,TimeL,TimeH1,TimeL1,dtube_cs_n,dtube_data);input ext_clk_25m ;//時鐘信號25MHzinput ext_rst_n ;//復位信號input seg_en ;//使能信號input set_en ;//設置使能信號input [ 3:0] set_segh ;//設置信號顯示高位input [ 3:0] set_segl ;//設置信號顯示高位input [ 3:0] TimeH ;//兩位輸入高位 [0]input [ 3:0] TimeL ;//兩位輸入低位 [1]input [ 3:0] TimeH1 ;//兩位輸入高位 [2]input [ 3:0] TimeL1 ;//兩位輸入低位 [3]output [ 3:0] dtube_cs_n ;//段選數據位output [ 6:0] dtube_data ;//位選數據位reg [ 3:0] dtube_cs_n ;reg [ 6:0] dtube_data ;reg [ 3:0] display_num ;//當前顯示數據reg [16:0] div_cnt ;//延時計數器計數位//延時計數器模塊always@ (posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n) begindiv_cnt <= 8'd0;endelse if(seg_en==1'b1)begindiv_cnt <= 8'd0;endelse if(div_cnt==17'd80000)begindiv_cnt <= 8'd0; endelse begindiv_cnt <= div_cnt+1'b1;endend//顯示當前的數據模塊always @(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)begin display_num <= 4'h0;endelse if(div_cnt < 17'd20000)beginif(set_en==1'b0)begindisplay_num <= TimeL;endelse begindisplay_num <=set_segl;endendelse if((div_cnt>17'd20000)&(div_cnt <17'd40000))beginif(set_en==1'b0)begindisplay_num <= TimeH;endelse begindisplay_num<=set_segh;endendelse if((div_cnt>17'd40000)&(div_cnt < 17'd60000))begindisplay_num <=TimeL1;endelse begindisplay_num <=TimeH1;endend//段選數據譯碼模塊(共陰數碼管)always @(*)beginif(!ext_rst_n)begin dtube_data <= 8'h00;endelse begincase(display_num) 4'h0: dtube_data <= 8'h3f;4'h1: dtube_data <= 8'h06;4'h2: dtube_data <= 8'h5b;4'h3: dtube_data <= 8'h4f;4'h4: dtube_data <= 8'h66;4'h5: dtube_data <= 8'h6d;4'h6: dtube_data <= 8'h7d;4'h7: dtube_data <= 8'h07;4'h8: dtube_data <= 8'h7f;4'h9: dtube_data <= 8'h6f;default:dtube_data <= 8'h00;endcaseendend
//位選選譯模塊always @(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n) begindtube_cs_n <= 4'b1111;endelse if(seg_en==1'b1)begindtube_cs_n <= 4'b1111;endelse if(div_cnt <= 17'd20000)begindtube_cs_n <= 4'b1110;endelse if((div_cnt>17'd20000)&(div_cnt <=17'd40000))begindtube_cs_n <= 4'b1101;end else if((div_cnt>17'd40000)&(div_cnt <=17'd60000)&(set_en==1'b0))begindtube_cs_n <= 4'b1011;endelse if((div_cnt>17'd60000)&(div_cnt <=17'd80000)&(set_en==1'b0))begindtube_cs_n <=4'b0111;endelse begindtube_cs_n <= 4'b1111;endendendmodule設置時間模塊
module set(ext_clk_25m,ext_rst_n,set_en,key_upup,key_down,key_entr,red,yellow,green,led,times1,times2);input ext_clk_25m;input ext_rst_n;input set_en;input key_down;input key_entr;input key_upup;output reg[7:0] red;output reg[7:0] green;output reg[7:0] yellow;output reg[3:0] times1;output reg[3:0] times2;output reg[7:6] led;//按鍵抖動判斷邏輯wire key; //所有的按鍵相與的結果，用于按鍵觸發判斷reg[3:0]keyr ; //按鍵值key的緩沖寄存器assign key =key_down&key_entr&key_upup;always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)keyr <=4'b1111;elsekeyr <={keyr[2:0],key};endwire key_neg;wire key_pos;assign key_neg=~keyr[2] &keyr [3];//有按鍵被按下assign key_pos=keyr[2] &~keyr [3];// 有按鍵被釋放//定時器計數邏輯，用于對按鍵的消抖的判斷reg [19:0] cnt;always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)begincnt <=20'd0;endelse if(key_pos||key_neg)begincnt <=20'd0;endelse if(cnt <20'd999_999)begincnt <= cnt +1'b1;endelse begincnt <=20'd0;endendreg[2:0]key_value_c;reg[2:0]key_value_n;//定時采取按鍵值always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginkey_value_c <=3'b111;key_value_n <=3'b111;endelse beginkey_value_n <=key_value_c;if(cnt ==20'd999_999)beginkey_value_c <={key_upup,key_entr,key_down};endelse;end endwire [2:0]key_press;assign key_press=key_value_n & ~key_value_c;always@(*)beginif(ext_rst_n==1'b0)begintimes1=red[7:4];endelse begintimes1=times[7:4];endendalways@(*)beginif(ext_rst_n==1'b0)begintimes2=red[3:0];endelse begintimes2=times[3:0];endend//顯示控制模塊reg [1:0]state;//設置狀態always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginstate<=2'b00;endelse if((key_press[1]==1'b1)&set_en==1'b1)beginif(state==2'b10)beginstate<=2'b00;endelse beginstate<=state+1'b1;endendendreg [7:0]times;//顯示的狀態模塊always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)begintimes<=red;endelse if(state==2'b00)begintimes<=red;endelse if(state==2'b01)begintimes<=green;endelse if(state==2'b10)begintimes<=yellow;endelse begintimes<=8'h00;endend//led指示模式模式always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(!ext_rst_n)beginled <=2'b11;endelse if(state==2'b00&set_en==1'b1)beginled<=2'b10;endelse if(state==2'b01&set_en==1'b1)beginled<=2'b01;endelse if(state==2'b10&set_en==1'b1)beginled<=2'b00;endelse beginled<=2'b11;endend//按鍵加減控制模塊(低位) 紅always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginred[3:0]<=4'h0;endelse if(state==2'b00)beginif(key_press[2]==1'b1)beginif(red==8'h99) beginred[3:0]<=4'h0;endelse if(red[3:0]==4'h9)beginred[3:0]<=4'h0;endelse beginred[3:0]<=red[3:0]+1'b1;endendelse if(key_press[0]==1'b1)beginif(red==8'h00)beginred[3:0] <=4'h9; endelse if(red[3:0]==4'h0)beginred[3:0]<=4'h9;endelse beginred[3:0]<=red[3:0]-1'b1;endendelse beginred[3:0]<=red[3:0];endendelse beginred[3:0]<=red[3:0];endend//按鍵加減控制模塊(高位) 紅always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginred[7:4]<=4'h2;endelse if(state==2'b00)beginif(key_press[2]==1'b1)beginif(red==8'h99) beginred[7:4]<=4'h0;endelse if(red[3:0]==4'h9)beginred[7:4]<=red[7:4]+1'b1;endelse beginred[7:4]<=red[7:4];endendelse if(key_press[0]==1'b1)beginif(red==8'h00)beginred[7:4]<=4'h9; endelse if(red[3:0]==4'h0)beginred[7:4] <=red[7:4]-1'b1;endelse beginred[7:4] <=red[7:4];endendelse beginred[7:4]<=red[7:4];endendelse beginred[7:4]<=red[7:4];endend//按鍵加減控制模塊(低位) 綠always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)begingreen[3:0]<=4'h5;endelse if(state==2'b01)beginif(key_press[2]==1'b1)beginif(green==8'h99) begingreen[3:0]<=4'h0;endelse if(green[3:0]==4'h9)begingreen[3:0]<=4'h0;endelse begingreen[3:0]<=green[3:0]+1'b1;endendelse if(key_press[0]==1'b1)beginif(green==8'h00)begingreen[3:0] <=4'h9; endelse if(green[3:0]==4'h0)begingreen[3:0]<=4'h9;endelse begingreen[3:0]<=green[3:0]-1'b1;endendelse begingreen[3:0]<=green[3:0];endendelse begingreen[3:0]<=green[3:0];endend//按鍵加減控制模塊(高位) 綠always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)begingreen[7:4]<=4'h1;endelse if(state==2'b01)beginif(key_press[2]==1'b1)beginif(green==8'h99) begingreen[7:4]<=4'h0;endelse if(green[3:0]==4'h9)begingreen[7:4]<=green[7:4]+1'b1;endelse begingreen[7:4]<=green[7:4];endendelse if(key_press[0]==1'b1)beginif(green==8'h00)begingreen[7:4]<=4'h9; endelse if(green[3:0]==4'h0)begingreen[7:4] <=green[7:4]-1'b1;endelse begingreen[7:4] <=green[7:4];endendelse begingreen[7:4]<=green[7:4];endendelse begingreen[7:4]<=green[7:4];endend//按鍵加減控制模塊(低位) 黃always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginyellow[3:0]<=4'h5;endelse if(state==2'b10)beginif(key_press[2]==1'b1)beginif(yellow==8'h99) beginyellow[3:0]<=4'h0;endelse if(yellow[3:0]==4'h9)beginyellow[3:0]<=4'h0;endelse beginyellow[3:0]<=yellow[3:0]+1'b1;endendelse if(key_press[0]==1'b1)beginif(yellow==8'h00)beginyellow[3:0] <=4'h9; endelse if(yellow[3:0]==4'h0)beginyellow[3:0]<=4'h9;endelse beginyellow[3:0]<=yellow[3:0]-1'b1;endendelse beginyellow[3:0]<=yellow[3:0];end endelse beginyellow[3:0]<=yellow[3:0];endend//按鍵加控制模塊(高位) 黃always@(posedge ext_clk_25m or negedge ext_rst_n)beginif(ext_rst_n==1'b0)beginyellow[7:4]<=4'h0;endelse if(state==2'b10)beginif(key_press[2]==1'b1)beginif(yellow==8'h99) beginyellow[7:4]<=4'h0;endelse if(yellow[3:0]==4'h9)beginyellow[7:4]<=yellow[7:4]+1'b1;endelse beginyellow[7:4]<=yellow[7:4];endendelse if(key_press[0]==1'b1)beginif(yellow==8'h00)beginyellow[7:4]<=4'h9; endelse if(yellow[3:0]==4'h0)beginyellow[7:4] <=yellow[7:4]-1'b1;endelse beginyellow[7:4] <=yellow[7:4];endendelse beginyellow[7:4]<=yellow[7:4];endendelse beginyellow[7:4]<=yellow[7:4];endend
endmodule設計頂層模塊的RTL圖
總結
以上是生活随笔為你收集整理的FPGA-任务五、十字路口交通控制灯器系统设计（二）的全部內容，希望文章能夠幫你解決所遇到的問題。
- 上一篇： [AtCoder Educational
- 下一篇： [AtCoder Educational