1. 描述

當我們想在操作系統里面查看網口和交換機連接的狀態信息，我們可以使用lldptool這個工具。

2.LLDP協議

LLDP是一個數據鏈路層發現協議，LLDP協議使得接入網絡的一臺設備可以將其主要的能力，管理地址，設備標識，接口標識等信息發送給接入同一個局域網絡的其它設備。lldptool工具采用的是LLDP協議，一般我們使用lldptool是為了得到設備的物理拓撲結構以及管理配置信息，比如說，和eth1網口相連的網絡交換機的Vlan ID是多少？網絡交換機的名稱是什么？網線插在網絡交換機的什么地方？

在這里我們不去討論LLDP協議的架構和具體時序狀態碼等，這里僅僅介紹怎么用它。

LLDP協議有四種工作模式：

TxRx：既發送也接收LLDP 幀

Tx? ? ：只發送不接收LLDP 幀

Rx：只接收不發送LLDP 幀

Disable：既不發送也不接收

一般設置LLDP工作在TxRx模式。

3.lldptool的命令格式

lldptool [options] [參數]

Options

-i [ifname]

specifies the network interface to which the command applies

-V [tlvid]

specifies the TLV identifier

The tlvid is an integer value used to identify specific LLDP TLVs. The tlvid value is the Type value for types not equal to 127 (the organizationally specific type). For organizationally specific TLVs, the tlvid is the value represented by the 3 byte OUI and 1 byte subtype - where the subtype is the lowest order byte of the tlvid.

The tlvid can be entered as a numerical value (e.g. 10 or 0xa), or for supported TLVs, as a keyword. Review the

lldptool?help output to see the list of supported TLV keywords.

-n

"neighbor" option for commands which can use it (e.g. get-tlv)

-g [bridge scope]

specify the bridge scope this command operates on. Allows to set and query all LLDP TLV modules for "nearest_bridge" (short: "nb"), "nearest_customer_bridge" ("ncb") and "nearest_nontpmr_bridge" ("nntpmrb") group mac addresses. Configurations are saved into independent sections in lldpad.conf. If no bridge scope is supplied this default to "nearest bridge" to preserve the previous behaviour.

-c

"config" option for TLV queries. Indicates that the query is for the configuration elements for the specified TLV. The argument list specifies the specific elements to query. If no arguments are listed, then all configuration elements for the TLV are returned.

-r

show raw client interface messages

-R

show only raw Client interface messages

Commands

license

show license information

-h, help

show usage information

-v, version

show version information

-S, stats

get LLDP statistics

-t, get-tlv

get TLV information

-T, set-tlv

set TLV information

-l, get-lldp

get LLDP parameters

-L, set-lldp

set LLDP parameters

-q, quit

exit from interactive mode

4.lldptool使用舉例

ip a查看啟用網口：

先看一些有沒有lldptool工具，如果沒有的話yum裝一下：

[root@wow ~]# service lldpad status

lldpad is stopped

[root@wow~]# service lldpad start

Starting lldpad: [ OK ]

[root@wow~]#

先設置lldptool的工作模式：

[root@wow ~]# lldptool set-lldp -i eth0 adminStatus=rxtx

adminStatus= rxtx　　#這樣就和網絡交換機建立了鄰居關系，接下來就可以查詢連接的交換機信息了

使用lldptool查看網口與交換機連接狀態：

[root@wow ~]# lldptool -t -n -i eth0

Chassis ID TLV

MAC:48:xx:xx:xx:xx:51　　#mac地址Port ID TLV

Ifname: GE1/0/1#網線插在交換機上的端口位置Time to Live TLV120System Name TLV

xx-xx-CE5850-xxxxx#交換機設備名System Description TLV

Huawei Versatile Routing Platform Software

VRP (R) software, Version8.150(CE5855EI V200R002C50SPC800)

Copyright (C)2012-2017Huawei Technologies Co., Ltd.

HUAWEI CE5855-xxxx-xxx　　#華為的交換機

System Capabilities TLV

System capabilities: Bridge, Router

Enabled capabilities: Bridge, Router

Management Address TLV

IPv4: xx.xxx.xxx.xx　　#ip地址

Ifindex:4OID:+[)

Port VLAN ID TLV

PVID:Port and Protocol VLAN ID TLV

PVID:0, not supported, not enabled

VLAN Name TLV

VID3652: Name VLAN3652

MAC/PHY Configuration Status TLV

Auto-negotiation supported and enabled

PMD auto-negotiation capabilities: 0xxxxxMAU type:1000BaseXFD

Link Aggregation TLV

Aggregation capable

Currently not aggregated

Aggregated Port ID:0Maximum Frame Size TLV9216End of LLDPDU TLV

[root@wow~]#

如果想利用lldptool對網口進行一些設置，可以參考手冊，下面是在Linux上找男人看到的一些例子：

Configure LLDP adminStatus to Receive and Transmit forinterface eth2　　#為網口eth2配置LLDP的收發工作模式

lldptool-L -i eth2 adminStatus=rxtx

lldptool set-lldp -i eth2 adminStatus=rxtx

Disable the LLDP adminStatusforall interfaces　　#讓所有網口都不可用LLDP

lldptool set-lldp adminStatus=disabled

Query the LLDP adminStatusforinterface eth3　　#查詢網口eth3的LLDP狀態

lldptool-l -i eth3 adminStatus

lldptool get-lldp -i eth3 adminStatus

Query the LLDP statisticsforinterface eth3 　　#查詢網口eth3的統計信息

lldptool-S -i eth3 adminStatus

lldptool stats-i eth3 adminStatus

Query the local TLVswhich are being transmitted fora given interface: 　　#查詢為給定接口傳輸的本地

lldptool-t -i eth3

lldptool get-tlv -i eth3

Query the received neighbor TLVs received on a given interface:　　#查詢給定接口上收到的接收鄰居TLV

lldptool-t -n -i eth3

lldptool get-tlv -n -i eth3

Query the value of the System Description TLV as received from the neighbor on a given interface:

lldptool-t -n -i eth3 -V sysDesc

lldptool get-tlv -n -i eth3 -V 6Disable transmit of the IEEE802.3 MAC/PHY Configuration Status TLV fora given interface:

lldptool-T -i eth3 -V macPhyCfg enableTx=no

lldptool set-tlv -i eth3 -V 0x120f01 enableTx=no

Enable transmit of the Port Description TLVforall interfaces:

lldptool-T -V portDesc enableTx=yes

lldptool set-tlv -V 4 enableTx=yes

Query value of the transmit settingfor the Port Description TLV fora given interface:

lldptool-t -V portDesc -c enableTx

lldptool get-tlv -V 4 -c enableTx

Set a Management Address TLV on eth3 to carry IPv4 address192.168.10.10lldptool-T -i eth3 -V mngAddr ipv4=192.168.10.10Set a Management Address TLV on eth3 to carry IPv6 address ::192.168.10.10lldptool-T -i eth3 -V mngAddr ipv6=::192.168.10.10Get the configured IPv4 addressforthe Management Address TLV on eth3

lldptool-t -i eth3 -V mngAddr-c ipv4

Get all configured attributesforthe Management Address TLV on eth3

lldptool-t -i eth3 -V mngAddr -c

Query the current DCBX mode that will be usediflldpad is restarted. (this is not a persistent setting)

lldptool-t-i eth3 -V IEEE-DCBX -c mode

Reset the DCBX mode to be'auto' (start inIEEE DCBX mode) after the next lldpad restart

lldptool-T -i eth3 -V IEEE-DCBX mode=reset

Enable transmit of the Edge Virtual Bridging TLVforinterface eth4

lldptool-i eth4-T -V evbCfg enableTx=yes

Configure EVB TLV to set reflective relay and RTE,ECP and VDP capabilities

lldptool-T -i eth4 -V evbCfg fmode=reflectiverelay

lldptool-T -i eth4 -V evbCfg capabilities=rte,ecp,vdp

Enable transmit of the VDPforinterface eth4

lldptool-i eth4 -T -V vdp enableTx=yes

Configurations per port have higher precedence than global configurations.

總結

以上是生活随笔為你收集整理的mysql lisensce_Linux之lldptool命令的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。