四路由器的OSPF DR ，BDR
生活随笔
收集整理的這篇文章主要介紹了
四路由器的OSPF DR ，BDR
小編覺得挺不錯的,現在分享給大家,幫大家做個參考.
網絡結構為四個路器與一個交換機直連，在單區域內配置OSPF： 路由器一： Router>en
Router#conf t
Enter configuration commands, one per line.? End with CNTL/Z.
Router(config)#hostname router1
router1(config)#int f0/0
router1(config-if)#ip add 192.168.1.1 255.255.255.0
router1(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router1(config-if)#ip ospf priority 100
router1(config-if)#exit
router1(config)#router ospf 1
router1(config-router)#network 192.168.1.0 0.0.0.255 area 0
router1(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
router1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
router1# 路由器2： Router>en
Router#conf t
Enter configuration commands, one per line.? End with CNTL/Z.
Router(config)#hostname router2
router2(config)#int f0/0
router2(config-if)#ip add 192.168.1.2 255.255.255.0
router2(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router2(config-if)#exit
router2(config)#router ospf 2
router2(config-router)#network 192.168.1.0 0.0.0.255 area 0
router2(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
router2#copy running-config
00:11:15: %OSPF-5-ADJCHG: Process 2, Nbr 192.168.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done
% Incomplete command.
router2#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
router2# 路由器3： Router>en
Router#conf t
Enter configuration commands, one per line.? End with CNTL/Z.
Router(config)#hostname router3
router3(config)#int f0/0
router3(config-if)#ip add 192.168.1.3 255.255.255.0
router3(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router3(config-if)#ip ospf priority 150
router3(config-if)#exit
router3(config)#router ospf 3
router3(config-router)#network 192.168.1.0 0.0.0.255 area 0
router3(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
router3#
00:14:16: %OSPF-5-ADJCHG: Process 3, Nbr 192.168.1.2 on FastEthernet0/0 from LOADING to FULL, Loading Done
router3#copy running
00:14:24: %OSPF-5-ADJCHG: Process 3, Nbr 192.168.1.1 on FastEthernet0/0 from EXCHANGE to FULL, Exchange Done
% Incomplete command.
router3#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
router3# 路由器4： Router>en
Router#conf t
Enter configuration commands, one per line.? End with CNTL/Z.
Router(config)#hostname router4
router4(config)#int f0/0
router4(config-if)#ip add 192.168.1.4 255.255.255.0
router4(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router4(config-if)#ip ospf priority 0
router4(config-if)#exit
router4(config)#router ospf 4
router4(config-router)#network 192.168.1.0 0.0.0.255 area 0
router4(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
router4#
00:18:05: %OSPF-5-ADJCHG: Process 4, Nbr 192.168.1.2 on FastEthernet0/0 from LOADING to FULL, Loading Done
00:18:05: %OSPF-5-ADJCHG: Process 4, Nbr 192.168.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done
router4#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
router4# 測試結果： router1#ping 192.168.1.2 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/53/63 ms router1#ping 192.168.1.3 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/56/63 ms router1#ping 192.168.1.4 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/56/79 ms
router1#ping 192.168.1.2 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/53/63 ms router1#ping 192.168.1.3 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/56/63 ms router1#ping 192.168.1.4 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/56/79 ms
查看OSPF信息： router1#sh ip ospf neighbor detail
?Neighbor 192.168.1.2, interface address 192.168.1.2
??? In the area 0 via interface FastEthernet0/0
??? Neighbor priority is 1, State is FULL, 6 state changes
??? DR is 192.168.1.3 BDR is 192.168.1.1
??? Options is 0x00
??? Dead timer due in 00:00:39
??? Neighbor is up for 00:02:00
??? Index 1/1, retransmission queue length 0, number of retransmission 0
??? First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
??? Last retransmission scan length is 0, maximum is 0
??? Last retransmission scan time is 0 msec, maximum is 0 msec
?Neighbor 192.168.1.3, interface address 192.168.1.3
??? In the area 0 via interface FastEthernet0/0
??? Neighbor priority is 150, State is FULL, 5 state changes
??? DR is 192.168.1.3 BDR is 192.168.1.1
??? Options is 0x00
??? Dead timer due in 00:00:31
??? Neighbor is up for 00:01:58
??? Index 2/2, retransmission queue length 0, number of retransmission 0
??? First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
??? Last retransmission scan length is 0, maximum is 0
??? Last retransmission scan time is 0 msec, maximum is 0 msec
?Neighbor 192.168.1.4, interface address 192.168.1.4
??? In the area 0 via interface FastEthernet0/0
??? Neighbor priority is 0, State is FULL, 6 state changes
??? DR is 192.168.1.3 BDR is 192.168.1.1
??? Options is 0x00
??? Dead timer due in 00:00:35
??? Neighbor is up for 00:01:54
??? Index 3/3, retransmission queue length 0, number of retransmission 0
??? First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
??? Last retransmission scan length is 0, maximum is 0
??? Last retransmission scan time is 0 msec, maximum is 0 msec
router1# 查看端品： router1#sh ip ospf int
FastEthernet0/0 is up, line protocol is up
? Internet address is 192.168.1.1/24, Area 0
? Process ID 1, Router ID 192.168.1.1, Network Type BROADCAST, Cost: 1
? Transmit Delay is 1 sec, State BDR, Priority 100
? Designated Router (ID) 192.168.1.3, Interface address 192.168.1.3
? Backup Designated Router (ID) 192.168.1.1, Interface address 192.168.1.1
? Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
??? Hello due in 00:00:06
? Index 1/1, flood queue length 0
? Next 0x0(0)/0x0(0)
? Last flood scan length is 1, maximum is 1
? Last flood scan time is 0 msec, maximum is 0 msec
? Neighbor Count is 3, Adjacent neighbor count is 3
??? Adjacent with neighbor 192.168.1.2
??? Adjacent with neighbor 192.168.1.3? (Designated Router)
??? Adjacent with neighbor 192.168.1.4
? Suppress hello for 0 neighbor(s) 測試結果OK****************************^--^
Router#conf t
Enter configuration commands, one per line.? End with CNTL/Z.
Router(config)#hostname router1
router1(config)#int f0/0
router1(config-if)#ip add 192.168.1.1 255.255.255.0
router1(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router1(config-if)#ip ospf priority 100
router1(config-if)#exit
router1(config)#router ospf 1
router1(config-router)#network 192.168.1.0 0.0.0.255 area 0
router1(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
router1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
router1# 路由器2： Router>en
Router#conf t
Enter configuration commands, one per line.? End with CNTL/Z.
Router(config)#hostname router2
router2(config)#int f0/0
router2(config-if)#ip add 192.168.1.2 255.255.255.0
router2(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router2(config-if)#exit
router2(config)#router ospf 2
router2(config-router)#network 192.168.1.0 0.0.0.255 area 0
router2(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
router2#copy running-config
00:11:15: %OSPF-5-ADJCHG: Process 2, Nbr 192.168.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done
% Incomplete command.
router2#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
router2# 路由器3： Router>en
Router#conf t
Enter configuration commands, one per line.? End with CNTL/Z.
Router(config)#hostname router3
router3(config)#int f0/0
router3(config-if)#ip add 192.168.1.3 255.255.255.0
router3(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router3(config-if)#ip ospf priority 150
router3(config-if)#exit
router3(config)#router ospf 3
router3(config-router)#network 192.168.1.0 0.0.0.255 area 0
router3(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
router3#
00:14:16: %OSPF-5-ADJCHG: Process 3, Nbr 192.168.1.2 on FastEthernet0/0 from LOADING to FULL, Loading Done
router3#copy running
00:14:24: %OSPF-5-ADJCHG: Process 3, Nbr 192.168.1.1 on FastEthernet0/0 from EXCHANGE to FULL, Exchange Done
% Incomplete command.
router3#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
router3# 路由器4： Router>en
Router#conf t
Enter configuration commands, one per line.? End with CNTL/Z.
Router(config)#hostname router4
router4(config)#int f0/0
router4(config-if)#ip add 192.168.1.4 255.255.255.0
router4(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
router4(config-if)#ip ospf priority 0
router4(config-if)#exit
router4(config)#router ospf 4
router4(config-router)#network 192.168.1.0 0.0.0.255 area 0
router4(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
router4#
00:18:05: %OSPF-5-ADJCHG: Process 4, Nbr 192.168.1.2 on FastEthernet0/0 from LOADING to FULL, Loading Done
00:18:05: %OSPF-5-ADJCHG: Process 4, Nbr 192.168.1.1 on FastEthernet0/0 from LOADING to FULL, Loading Done
router4#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
router4# 測試結果： router1#ping 192.168.1.2 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/53/63 ms router1#ping 192.168.1.3 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/56/63 ms router1#ping 192.168.1.4 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/56/79 ms
router1#ping 192.168.1.2 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/53/63 ms router1#ping 192.168.1.3 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/56/63 ms router1#ping 192.168.1.4 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 47/56/79 ms
查看OSPF信息： router1#sh ip ospf neighbor detail
?Neighbor 192.168.1.2, interface address 192.168.1.2
??? In the area 0 via interface FastEthernet0/0
??? Neighbor priority is 1, State is FULL, 6 state changes
??? DR is 192.168.1.3 BDR is 192.168.1.1
??? Options is 0x00
??? Dead timer due in 00:00:39
??? Neighbor is up for 00:02:00
??? Index 1/1, retransmission queue length 0, number of retransmission 0
??? First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
??? Last retransmission scan length is 0, maximum is 0
??? Last retransmission scan time is 0 msec, maximum is 0 msec
?Neighbor 192.168.1.3, interface address 192.168.1.3
??? In the area 0 via interface FastEthernet0/0
??? Neighbor priority is 150, State is FULL, 5 state changes
??? DR is 192.168.1.3 BDR is 192.168.1.1
??? Options is 0x00
??? Dead timer due in 00:00:31
??? Neighbor is up for 00:01:58
??? Index 2/2, retransmission queue length 0, number of retransmission 0
??? First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
??? Last retransmission scan length is 0, maximum is 0
??? Last retransmission scan time is 0 msec, maximum is 0 msec
?Neighbor 192.168.1.4, interface address 192.168.1.4
??? In the area 0 via interface FastEthernet0/0
??? Neighbor priority is 0, State is FULL, 6 state changes
??? DR is 192.168.1.3 BDR is 192.168.1.1
??? Options is 0x00
??? Dead timer due in 00:00:35
??? Neighbor is up for 00:01:54
??? Index 3/3, retransmission queue length 0, number of retransmission 0
??? First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
??? Last retransmission scan length is 0, maximum is 0
??? Last retransmission scan time is 0 msec, maximum is 0 msec
router1# 查看端品： router1#sh ip ospf int
FastEthernet0/0 is up, line protocol is up
? Internet address is 192.168.1.1/24, Area 0
? Process ID 1, Router ID 192.168.1.1, Network Type BROADCAST, Cost: 1
? Transmit Delay is 1 sec, State BDR, Priority 100
? Designated Router (ID) 192.168.1.3, Interface address 192.168.1.3
? Backup Designated Router (ID) 192.168.1.1, Interface address 192.168.1.1
? Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
??? Hello due in 00:00:06
? Index 1/1, flood queue length 0
? Next 0x0(0)/0x0(0)
? Last flood scan length is 1, maximum is 1
? Last flood scan time is 0 msec, maximum is 0 msec
? Neighbor Count is 3, Adjacent neighbor count is 3
??? Adjacent with neighbor 192.168.1.2
??? Adjacent with neighbor 192.168.1.3? (Designated Router)
??? Adjacent with neighbor 192.168.1.4
? Suppress hello for 0 neighbor(s) 測試結果OK****************************^--^
轉載于:https://blog.51cto.com/ouhuahe3628/121069
總結
以上是生活随笔為你收集整理的四路由器的OSPF DR ，BDR的全部內容，希望文章能夠幫你解決所遇到的問題。
- 上一篇： 幸福是什么
- 下一篇： 爱情麻辣烫：浓缩了中华美食精华与火锅的精