dSPACE Mid-Size Simulator Introduction
dSPACE Simulator Mid-Size是一種閉環的硬件在環仿真器,其有以下特性:
-
支持信號調理
-
支持給ECU提供等效或真實負載
-
失效模擬
-
兩路電壓系統支持遠程控制供電
主機需配備一塊鏈接板卡-Link Board來進行總線接口連接。dSAPCE提供3種不同類型的Link Board來匹配主機不同的總線類型(有ISA/PCI/PCMIA接口)。總線接口用來將real-time model下載到仿真器中,對仿真過程進行控制。主機和仿真器之間通過RS232串口來控制故障注入單元(FIU).
dSPACE Mid-Size仿真包含以下部件:
-
處理器板塊DS1005/DS1006
-
I/O板卡DS2211/DS2202
-
鏈接板卡DS814
-
Load/FIU單元:5個DS790負載板卡,每個板卡包含10個通道,可配置低功率的阻性或感性負載;5個DS791故障注入單元,每個單元包含10個通道,可配置低功率的阻性或感性負載
-
一個DS686?Backplane
-
一個DS685 Midplane
-
可遠程控制的供電單元
DS1006 Processor Board
The DS1006 Processor Board is based on a single-core or a multicore AMD Opteron TM processor. This real time processor (RTP) is the main processing unit. It can access modular I/O boards via its PHS bus. It is multiprocessing-capable via the (optional) DS911 Gigalink Module.
DS1006處理器板基于單核或多核AMD?Opteron?TM處理器。此實時處理器 (RTP) 是主要的處理單元。它可以通過其PHS總線訪問模塊化I / O板。它通過(可選)DS911 千兆鏈路模塊實現多處理能力。
Figure 1. DS1006 Processor Board
DS2211 I/O Board
The DS2211 HIL I/O Board is tailored to simulate and measure automotive signals. It combines a variety of typical HIL I/O functions on one board. The board also contains signal conditioning for typical signal levels of 12 V and 42 V automotive systems.
DS2211 HIL I/O板專為仿真和測量汽車信號而定制。它將各種典型的HIL I/O功能組合在一塊電路板上。該板還包含針對 12 V 和 42 V 汽車系統典型信號電平的信號調理。
Figure 2. DS2211 I/O Board
DS4302 CAN Interface Board
The DS4302 CAN Interface Board allows data transfer between dSPACE real-time systems and various other control units via 4 CAN bus interfaces.
DS4302 CAN接口板允許通過4個CAN總線接口在dSPACE實時系統和其他各種控制單元之間傳輸數據。
Figure 3. DS4302 CAN Interface Board
DS4505 & DS4340 & DS4342
The DS4505 Interface Board together with different interface modules allows data transfer between dSPACE real-time systems and various other control units:
-
Via FlexRay bus by means of DS4340 FlexRay Interface Modules
-
Via CAN bus by means of DS4342 CAN FD Interface Modules
DS4505接口板卡與不同的接口模塊一起,允許在dSPACE實時系統和各種其它控制單元之間傳輸數據:
-
選擇DS4340?FlexRay接口模塊,支持FlexRay總線通信
-
選擇DS4342 CAN FD接口模塊,支持CAN FD總線通信
Figure 4. DS4505 Interface Board(Left); DS4342 CAN FD Interface Module(Middle); DS4340 FlexRay Interface Module(Right)
DS790 Load Card
dSPACE Simulator Mid-Size is equipped with five low-power load cards (DS790 Load Card) with the following characteristics:
-
10 single-ended loads or 5 double-ended loads per card, or mixed
-
2 W maximum continuous power per load
-
50 W maximum continuous power per load/FIU unit
-
6 A maximum load current
-
LED indicators displaying current load states, battery voltage and switched voltage
-
Front panel for measurement or connection of real loads
dSPACE Mid-Size模擬器配備五個低功耗負載板卡(DS790 負載板卡),具有以下特性:
-
每張卡 10 個單端負載或 5 個雙端負載,或混合負載
-
每個負載支持2 W 最大連續功率
-
每個負載/FIU 單元的最大連續功率為 50 W
-
6 A 最大負載電流
-
顯示當前負載狀態、電池電壓和開關電壓的 LED 指示燈
-
用于測量或連接實際負載的前面板
Figure 5. DS790 Load Card
Loads are installed on the load cards inside the simulator or plugged to the panel on the front of the simulator. Inside the simulator there are load sockets that the loads can be connected to. One load socket connects the load to the ECU channel, the other load socket connects the load to a high rail or to the adjacent channel (for double-ended loads).
負載安裝在模擬器內部的負載卡上,或插入模擬器正面的面板上。在模擬器內部,有負載插座,負載可以連接到。一個負載插座將負載連接到ECU通道,另一個負載插座將負載連接到高軌或相鄰通道(用于雙端負載)。
Figure 6. Install a single-ended load on the load socket(Left); Install a double-ended load on the load socket(Right)
DS791 Failure Insertion Unit
A Load/FIU unit is equipped with 5 failure insertion units (DS791 FIU) with the following characteristics:
-
Support of 50 ECU pins in total (each DS791 Failure Insertion Units (FIU) have 10 channels.)Failure simulation
-
for ECU outputs (Channels are directly connected to the pins of the ECU 1 connector, which contains the signals for the ECU outputs)
-
Remote control using Control Desk's Failure Simulation module
-
Simulation of short circuits:
-
Short circuits from one or more ECU pins to ground or battery voltage via fail plane 1 or fail plane
-
Short circuits between two or more ECU pins via fail plane 1 or fail plane 2
-
-
Cable break simulation
-
Simultaneous simulation of multiple failures
-
6 A maximum load current
負載/FIU 單元配備 5 個故障插入單元 (DS791 FIU),具有以下特性:
-
總共支持50個ECU引腳(每個DS791故障插入單元(FIU)有10個通道)故障模擬
-
用于 ECU 輸出(通道直接連接到 ECU 1 連接器的引腳,該連接器包含 ECU 輸出的信號)
-
使用ControlDesk的故障模擬模塊進行遠程控制
-
短路模擬:
-
通過故障面板將一個或多個 ECU 引腳短路到地或電池電壓
-
兩個或多個ECU引腳之間短路
-
-
開路模擬
-
同時模擬多個故障
-
最大6 A的負載電流
The DS791 FIUs are connected to the ECU 1 connector and the DS685 Midplane.
DS791 FIU 連接到 ECU 1 連接器和 DS685 背板。
Figure 7. DS791 Failure Insertion Unit
總結
以上是生活随笔為你收集整理的dSPACE Mid-Size Simulator Introduction的全部內容,希望文章能夠幫你解決所遇到的問題。
- 上一篇: Vs Code Vetur can‘t
- 下一篇: eMule 无法连接到ed2k 的解决方