R329开发板系列教程之二|实机运行aipu程序
生活随笔
收集整理的這篇文章主要介紹了
R329开发板系列教程之二|实机运行aipu程序
小編覺得挺不錯的,現在分享給大家,幫大家做個參考.
首發極術社區
如對Arm相關技術感興趣，歡迎私信aijishu20加入技術微信群。
通過周易AIPU 部署及仿真教程，大家應該都完成了在PC上使用模擬器仿真執行了模型，本節教程將帶領大家進行真機上的第一次模型運行。
本系列教程由矽速科技撰寫提供。 本章節網盤資料：
鏈接：https://pan.baidu.com/s/1vpPH_pHKQ_w3Z4DTxJTixg
提取碼：4tni
板卡開箱介紹
考慮到可能有些純軟件工程師第一次接觸硬件板卡，在此進行下板卡的硬件基礎介紹，方便后續操作。
首先可以從網盤下載產品規格書，大致熟悉下R329開發板的基礎信息。
收到快遞后，開箱可得一個小巧的PP盒，打開即MaixSense板卡，芯片面為：
注意芯片上已粘貼了散熱片，所以看不到R329 logo
板載了wifi+bt模塊，那一小根是天線
那個小按鍵是FEL按鍵，供下載系統到nand使用，目前未使用
復位按鍵在底板上空貼
側面總共4個用戶按鍵可供自定義使用
屏幕面如下：
注意攝像頭模塊是使用 type-C，可以正反接作為前后攝像頭。
屏幕為1.54寸 IPS屏，240x240分辨率
屏幕下面板子邊緣有雙顆硅麥，可用于雙麥降噪
屏幕與底板使用磁貼吸附，需要時可分離
側面如圖：
紅圈圈出來的地方為TF卡槽，后面插卡啟動用
注意板載內置了揚聲器，系統正常啟動后會有開機聲
系統燒錄配置
系統燒錄啟動
從以下鏈接下載系統燒錄固件及Tina系統鏡像（tina_r329-evb5_uart0.img）
Tina系統是全志魔改OpenWRT1404的系統，系統比較精簡，我們也為該系統下打包了各種常用的應用程序，如python3等。
準備一張512MB以上的TF卡，插入讀卡器，插入電腦，按下圖所示選擇固件，啟動卡，點擊燒卡，等待約半分鐘即可燒錄完成系統。
拔出TF卡，插入R329開發板的卡槽（方向為金手指朝下），用type-C線連接板子與電腦，即可啟動板卡。
啟動時有引擎提示音，請勿驚慌_
MaixSense已經板載了usb轉串口，所以插上type-C后電腦上會出現虛擬串口，大家可以使用Xshell/minicom等工具軟件進入串口終端操作。
附錄有成功啟動的log信息，以供比對參照。
wifi配置
為了后續傳輸文件方便，我們先進行wifi配置。
首先執行ifconfig可見wlan0, 說明wifi驅動正確加載。接下來有兩種方式配網。
傳統方式
wpa_supplicant -iwlan0 -Dnl80211 -c/etc/wifi/wpa_supplicant.conf -I/etc/wifi/wpa_supplicant_overlay.conf -O/etc/wifi/sockets修改 /etc/wifi/wpa_supplicant.conf network={ ssid="your ssid" psk="your password" } 修改后重啟網絡并獲取IP udhcpc -i wlan0快捷方式
Tina系統內置了快速配網指令， 一行指令完成配網：
wifi_connect_ap_test ssid password配網完成后ifconfig即可看到自己的ip，說明聯網成功，此時即可ssh遠程連接板卡進行指令和文件操作。
快速測試 aipu
首先插入aipu.ko這個內核模塊來使能周易aipu驅動：
root@TinaLinux:~/maix_sense# insmod aipu.ko [ 48.736664] aipu: loading out-of-tree module taints kernel. [ 48.744649] armchina aipu: AIPU KMD probe start... [ 48.750113] armchina aipu: KMD version: release 3.0.13 [ 48.755915] armchina aipu: no interrupts-reg specified [ 48.762214] armchina aipu: AIPU is not behind an IOMMU [ 48.768015] armchina aipu: AIPU DRAM mem type is [CMA default] [ 48.774579] armchina aipu: dma_alloc_attrs failed (bytes: 0x2600000, attrs 0) [ 48.782606] armchina aipu: AIPU core #0 detected: zhouyi-v1-0600 [ 48.789699] armchina aipu: AIPU Initial Status: 0x70000 [ 48.795601] armchina aipu: ########## AIPU CORE 0: ZHOUYI V1 ########## [ 48.803037] armchina aipu: # ISA Version Register: 0x0 [ 48.808817] armchina aipu: # TPC Feature Register: 0x10101 [ 48.814987] armchina aipu: # SPU Feature Register: 0x0 [ 48.820772] armchina aipu: # HWA Feature Register: 0x10111 [ 48.826939] armchina aipu: # Revision ID Register: 0x0 [ 48.832719] armchina aipu: # Memory Hierarchy Feature Register: 0x170 [ 48.839959] armchina aipu: # Instruction RAM Feature Register: 0x0 [ 48.847006] armchina aipu: # TEC Local SRAM Feature Register: 0x312 [ 48.854245] armchina aipu: # Global SRAM Feature Register: 0x10 [ 48.861395] armchina aipu: # Instruction Cache Feature Register:0x233 [ 48.868633] armchina aipu: # Data Cache Feature Register: 0x70030 [ 48.876066] armchina aipu: # L2 Cache Feature Register: 0x0 [ 48.883156] armchina aipu: ############################################ [ 48.890593] armchina aipu: initialize AIPU core #0 done運行內置測試模型：
root@TinaLinux:~/maix_sense# ./run.sh -c kws_gru [TEST RUN INFO] Run benchmark test with benchmark kws_gru [TEST INFO] AIPU load graph succ[ 598.648094] armchina aipu: [Job 65536 of Thread 1744] trigger job running done essfully. [TEST INFO] Job #65536 Test Result Check PASS! (1/1) [TEST INFO] job cleaned. [TEST RUN INFO] memory section dump files saved under: ./output/kws_gru-pass-1970-01-01-08-20-27這表示內置例程模型測試通過
快速測試自己的模型
首先在之前的docker鏡像中，進行aipu的build操作，得到aipu.bin文件，該文件即aipu的可執行文件。
仿照內置例程，在models下新建自己的目錄，將 aipu.bin拷入該目錄，
并拷入輸入數據，重命名為input0.bin, 以及正確的輸出數據（即仿真的output），重命名為output.bin，接下來即可類似進行自己模型的驗證測試。
上手編寫簡單測試程序
由于Tina系統為端側嵌入式設備優化的系統，所以沒有內置工具鏈，這里我們需要進行交叉編譯來編譯我們的測試程序。
工具鏈已經附在上面的網盤里，即 toolchain.tar.gz ，解壓即可
最小測試例程代碼在 網盤的zhouyi_bmp.zip下。
該例程可以測試imagenet 分類模型的運行效果，使用了周易的 standard_api, 用戶可以根據該例程自行修改自己模型的運行程序。
以下為測試mobilenet_v2的結果, 可見執行時間為46ms，執行結果正確。
以下為測試 resnet50 的結果, 可見執行時間為133ms，執行結果正確。
root@TinaLinux:~/maix_sense# ./zhouyi models/resnet50/aipu.bin test.bmp 1 Zhouyi min test program: Usage: ./zhouyi aipu.bin input.bmp signedsigned=0, uint8 output; =1, int8 outputNOTE: bmp file width/height must correct Step 1 init ctx handle cost 0 ms [DEMO INFO] AIPU load graph successfully. Step 2 load graph cost 100 ms Step 3 alloc tensor buffers cost 0 msModel input: W=224, H=224, C =3, size=150528 [75329.628868] armchina aipu: [Job 65536 of Thread 2474] trigger job running done Step 4 read pic cost 10 ms Step 5 AIPU_create_job cost 0 ms Step 5 AIPU_finish_job cost 133 ms Decode Result:0: class 230, prob 101; label: Shetland sheepdog, Shetland sheep dog, Shetland1: class 231, prob 97; label: collie2: class 169, prob 57; label: borzoi, Russian wolfhound3: class 232, prob 54; label: Border collie4: class 157, prob 45; label: papillon Step 5 decode_result cost 0 ms附錄
串口啟動信息
[276]HELLO! BOOT0 is starting! [279]BOOT0 commit : 97444f5 [281]set pll start [284]periph0 has been enabled [287]set pll end [289]board init ok [290]rtc[3] value = 0xf6f65006 [293]the chip id is 0x3 [296]the chip id is 0x3 [298]the chip id is 0x3 [300]the chip id is 0x3 [303]the chip id is 0x3 [305]chip id check OK [308][AUTO DEBUG] two rank and full DQ! [312][AUTO DEBUG] DDR3 try success [316][AUTO DEBUG] single rank and full DQ! [321][AUTO DEBUG] rank 0 row = 14 [324][AUTO DEBUG] rank 0 bank = 8 [328][AUTO DEBUG] rank 0 page size = 2 KB [332]DRAM BOOT DRIVE INFO: V0.171 [335]DRAM Type = 3 (2:DDR2,3:DDR3) [338]DRAMC read ODT off. [341]DRAM ODT off. [344]DRAM CLK = 774 MHz [346]DRAM SIZE =256 M [351]DRAM simple test OK. [354]dram size =256 [357]card no is 0 [358]sdcard 0 line count 4 [361][mmc]: mmc driver ver 2020-07-22 11:09 [371][mmc]: Wrong media type 0x0 [374][mmc]: ***Try SD card 0*** [394]mmc_read_info 787:region magic is not right, retry more time 0 [411]mmc_read_info 787:region magic is not right, retry more time 0 [429]mmc_read_info 787:region magic is not right, retry more time 0 [446]mmc_read_info 787:region magic is not right, go err 0 [452]dump info registers:[454] 0x107184 : [456]a1ff [457]b [458]60868689 [459]6088fb58 [460] [461][mmc]: RMCA FAIL! [463][mmc]: mmc read timing info fail [467][mmc]: force 25m [469][mmc]: mmc 0 bias 0 [472][mmc]: HSSDR52/SDR25 4 bit [475][mmc]: 25000000 Hz [478][mmc]: 29818 MB [480][mmc]: ***SD/MMC 0 init OK!!!*** [580]Loading boot-pkg Succeed(index=0). [584]Entry_name = u-boot [591]Entry_name = monitor [594]Entry_name = dtb [597]mmc not para [599]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):3eba4b6 NOTICE: BL3-1: Built : 10:18:25, 2020-05-21 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x43000000 ?OTICE: BL3-1: Next image spsr = 0x1d3U-Boot 2018.05 (Mar 29 2021 - 10:30:51 +0000) Allwinner Technology[00.655]CPU: Allwinner Family [00.657]Model: sun50iw11 I2C: ready [00.779]DRAM: 256 MiB [00.781]Relocation Offset is: 0cefc000 [00.805]secure enable bit: 0 [00.807]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=0Mhz [00.818]gic: sec monitor mode [00.821]flash init start [00.823]workmode = 0,storage type = 1 [00.826][mmc]: mmc driver ver uboot2018:2020-10-22 16:39:00 [00.837][mmc]: Using default timing para [00.840][mmc]: SUNXI SDMMC Controller Version:0x50300 [00.856][mmc]: card_caps:0x3000000a [00.859][mmc]: host_caps:0x3000003f [00.863]sunxi flash init ok [00.865]bmp_name=bootlogo.bmp 307254 bytes read in 17 ms (17.2 MiB/s) [00.912]Loading Environment from SUNXI_FLASH... OK [00.933]Item0 (Map) magic is bad [00.936]the secure storage item0 copy0 magic is bad [00.941]Item0 (Map) magic is bad [00.944]the secure storage item0 copy1 magic is bad [00.948]Item0 (Map) magic is bad [00.951]usb burn from boot delay time 0 weak:otg_phy_config [00.963]usb prepare ok [01.767]overtime [01.771]do_burn_from_boot usb : no usb exist partno erro : can't find partition private [01.781]update bootcmd [01.786]update dts Hit any key to stop autoboot: 0 [01.855]phase vdd-cpu: 0x00000000 [01.858]phase vdd-sys: 0x00000000 [01.861]phase vcc-pll: 0x00000000 [01.864]phase osc24m-on: 0x00000001 [01.867]phase pllcpu-off: 0x00000001 [01.871]phase pllperiph0-off: 0x00000001 [01.874]phase pllaudio0-off: 0x00000000 [01.878]phase pllaudio1-off: 0x00000001 [01.881]phase ahb1ahb2-to-32k: 0x00000001 [01.885]phase apb1-to-32k: 0x00000000 [01.889]phase apb2-to-32k: 0x00000001 [01.892]phase axi-to-32k: 0x00000001 [01.895]phase apbs0-to-32k: 0x00000000 [01.899]phase apbs1-to-32k: 0x00000000 [01.902]phase uart-off: 0x00000000 [01.905]phase nmi-wakeup: 0x00000000 [01.909]phase sleep-freq: 0x00005dc0 DSP VERSION IS smartx-r329-tina-v0.5.0-release-58-g87af487-dirty DSP0 booting from 0x100400... Android's image name: r329-evb5 [02.410]Starting kernel ...[02.413][mmc]: MMC Device 2 not found [02.416][mmc]: mmc 2 not find, so not exit [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.9.191 (dls@sipeed-ai) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #28 SMP PREEMPT Tue Jul 20 13:31:53 UTC 2021 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] cma: Reserved 96 MiB at 0x000000004a000000 [ 0.000000] On node 0 totalpages: 65536 [ 0.000000] DMA zone: 1024 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 65536 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 21 pages/cpu s46360 r8192 d31464 u86016 [ 0.000000] pcpu-alloc: s46360 r8192 d31464 u86016 alloc=21*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p7 rootwait init=/sbin/init rdinit=/rdinit partitions= cma=96M mac_addr= wifi_mac= bt_mac= selinux=0 specialstr= snum=5c000c29b2438561f8c pstore_blk.blkdev= pstore.update_ms=1000 androidboot.serialno=5c000c29b2438561f8c androidboot.hardware=sun50iw11p1 boot_type=1 androidboot.boot_type=1 androidboot.secure_os_exist=0 gpt=1 uboot_message=2018.05(03/29/2021-10:30:51) mbr_offset=1032192 [ 0.000000] PID hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.000000] Memory: 138624K/262144K available (7294K kernel code, 614K rwdata, 2084K rodata, 448K init, 277K bss, 25216K reserved, 98304K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff80087a0000 ( 7296 KB) [ 0.000000] .rodata : 0xffffff80087a0000 - 0xffffff80089b0000 ( 2112 KB) [ 0.000000] .init : 0xffffff80089b0000 - 0xffffff8008a20000 ( 448 KB) [ 0.000000] .data : 0xffffff8008a20000 - 0xffffff8008ab9808 ( 615 KB) [ 0.000000] .bss : 0xffffff8008ab9808 - 0xffffff8008afecf4 ( 278 KB) [ 0.000000] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] clk r_dsp_cache0 not found in of_sunxi_periph_cpus_clk_setup [ 0.000000] clk r_dsp_cache1 not found in of_sunxi_periph_cpus_clk_setup [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008190] Console: colour dummy device 80x25 [ 0.012412] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.022618] pid_max: default: 32768 minimum: 301 [ 0.027379] Mount-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.033722] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.041508] sched-energy: CPU device node has no sched-energy-costs [ 0.046921] Invalid sched_group_energy for CPU0 [ 0.051401] CPU0: update cpu_capacity 1024 [ 0.067519] ASID allocator initialised with 32768 entries [ 0.123753] Detected VIPT I-cache on CPU1 [ 0.123804] Invalid sched_group_energy for CPU1 [ 0.123807] CPU1: update cpu_capacity 1024 [ 0.123810] CPU1: Booted secondary processor [410fd034] [ 0.123894] Brought up 2 CPUs [ 0.138996] SMP: Total of 2 processors activated. [ 0.143687] CPU features: detected feature: 32-bit EL0 Support [ 0.149492] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.158811] CPU: All CPU(s) started at EL1 [ 0.160768] alternatives: patching kernel code [ 0.165338] Invalid sched_group_energy for CPU1 [ 0.169688] Invalid sched_group_energy for Cluster1 [ 0.174538] Invalid sched_group_energy for CPU0 [ 0.179044] Invalid sched_group_energy for Cluster0 [ 0.184393] devtmpfs: initialized [ 0.213690] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.217818] futex hash table entries: 512 (order: 4, 65536 bytes) [ 0.227236] atomic64_test: passed [ 0.227276] pinctrl core: initialized pinctrl subsystem [ 0.233408] NET: Registered protocol family 16 [ 0.238079] dump_class_init,857, success [ 0.252903] cpuidle: using governor menu [ 0.253583] vdso: 2 pages (1 code @ ffffff80087a6000, 1 data @ ffffff8008a24000) [ 0.259706] DMA: preallocated 256 KiB pool for atomic allocations [ 0.270771] sun50iw11p1-r-pinctrl r_pio: initialized sunXi PIO driver [ 0.279336] sun50iw11p1-pinctrl pio: initialized sunXi PIO driver [ 0.378577] pwm module init! [ 0.382391] sunxi-pm debug v3.10 [ 0.383167] SCSI subsystem initialized [ 0.384047] usbcore: registered new interface driver usbfs [ 0.389654] usbcore: registered new interface driver hub [ 0.394583] usbcore: registered new device driver usb [ 0.399657] sunxi_i2c_adap_init()2649 - init [ 0.404226] sunxi_i2c_probe()2372 - [i2c2] twi_drv_used = 1 [ 0.409310] sunxi_i2c_probe()2379 - [i2c2] twi_pkt_interval = 0 [ 0.415203] twi2 supply twi not found, using dummy regulator [ 0.420887] twi_request_gpio()458 - [i2c2] init name: (null) [ 0.426656] sunxi_i2c_dma_request()1088 - [i2c2] using dma0chan0 (tx) and dma0chan1 (rx)for DMA transfers [ 0.436428] sunxi_i2c_probe()2372 - [i2c1] twi_drv_used = 0 [ 0.441543] sunxi_i2c_probe()2379 - [i2c1] twi_pkt_interval = 0 [ 0.447439] twi1 supply twi not found, using dummy regulator [ 0.453140] twi_request_gpio()458 - [i2c1] init name: (null) [ 0.459448] Linux video capture interface: v2.00 [ 0.464422] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000 [ 0.470359] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000 [ 0.476708] ion_parse_dt_heap_common: id 6 type 6 name secure align 1000 [ 0.483504] ion_heap_create: Invalid heap type 6 [ 0.491054] Advanced Linux Sound Architecture Driver Initialized. [ 0.494558] Bluetooth: Core ver 2.22 [ 0.497469] NET: Registered protocol family 31 [ 0.501865] Bluetooth: HCI device and connection manager initialized [ 0.508196] Bluetooth: HCI socket layer initialized [ 0.513041] Bluetooth: L2CAP socket layer initialized [ 0.518100] Bluetooth: SCO socket layer initialized [ 0.524485] input: sunxi-keyboard as /devices/virtual/input/input0 [ 0.533711] clocksource: Switched to clocksource arch_sys_counter [ 0.547269] get androidboot.mode fail [ 0.548064] NET: Registered protocol family 2 [ 0.550224] TCP established hash table entries: 16 (order: -5, 128 bytes) [ 0.556454] TCP bind hash table entries: 16 (order: -4, 256 bytes) [ 0.562567] TCP: Hash tables configured (established 16 bind 16) [ 0.568668] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.574363] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.580810] NET: Registered protocol family 1 [ 0.585601] sunxi_spi_probe()2633 - [spi1] SPI DBI INTERFACE [ 0.590563] sunxi_spi_probe()2642 - [spi1] SPI MASTER MODE [ 0.596096] spi1 supply spi not found, using dummy regulator [ 0.601729] sunxi_spi_request_gpio()2252 - [spi1] Pinctrl init spi1 [ 0.607986] sunxi_spi_clk_init()2302 - [spi1] mclk 100000000 [ 0.613962] spi spi1: master is unqueued, this is deprecated [ 0.619175] sunxi_spi_probe()2723 - [spi1]: driver probe succeed, base ffffff800806c000, irq 256 [ 0.630657] workingset: timestamp_bits=61 max_order=16 bucket_order=0 [ 0.643313] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.646479] io scheduler noop registered [ 0.647412] io scheduler deadline registered [ 0.652043] io scheduler cfq registered (default) [ 0.657617] [LCD_FB] lcd_fb_init,line:159: [ 0.660263] [ 0.662212] [LCD_FB] lcd_fb_probe,line:65: [ 0.665801] [ 0.687280] [LCD_FB] lcd_fb_script_get_item,line:139: [ 0.687324] of_find_compatible_node allwinner,sunxi-lcd_fb1 fail [ 0.692936] [LCD_FB] disp_lcd_set_panel_funs,line:1068: [ 0.697714] lcd_panel_fun[0].cfg_panel_info is NULL [ 0.703328] [LCD_FB] Fb_map_kernel_logo,line:201: [ 0.707252] Fb_map_kernel_logo failed![LCD_FB] disp_lcd_spi_init,line:817: [ 0.7?[ 0.720299] uart uart0: get regulator failed [ 0.720316] uart0 supply uart not found, using dummy regulator [ 0.720557] uart0: ttyS0 at MMIO 0x2500000 (irq = 242, base_baud = 1500000) is a SUNXI [ 0.720577] sw_console_setup()2047 - console setup baud 115200 parity n bits 8, flow n [ 0.742473] [LCD_FB] lcd_fb_gpio_set_value,line:353:[ 0.742473] [LCD_FB] lcd_fb_gpio_set_value,line:353:[ 0.742496] console [ttyS0] enabled [ 0.742496] console [ttyS0] enabled [ 0.742500] bootconsole [earlycon0] disabled [ 0.742500] bootconsole [earlycon0] disabled[ 0.770412] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL [ 0.770818] [LCD_FB] lcd_fb_gpio_set_value,line:353: [ 0.770818] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL [ 0.792952] uart uart1: get regulator failed [ 0.797784] uart1 supply uart not found, using dummy regulator [ 0.804557] uart1: ttyS1 at MMIO 0x2500400 (irq = 243, base_baud = 1500000) is a SUNXI [ 0.814291] misc dump reg init [ 0.818051] Unable to detect cache hierarchy for CPU 0 [ 0.824111] sunxi-bt soc@03000000:bt: bt_power_num (4294967232) [ 0.830778] sunxi-bt soc@03000000:bt: Missing bt_io_regulator. [ 0.837341] sunxi-bt soc@03000000:bt: io_regulator_name ((null)) [ 0.844100] sunxi-bt soc@03000000:bt: request pincrtl handle for device [soc@03000000:bt] failed [ 0.854024] sunxi-bt soc@03000000:bt: bt_rst gpio=386 mul-sel=1 pull=1 drv_level=2 data=0 [ 0.863627] sunxi-bt soc@03000000:bt: clk_name () [ 0.868965] sunxi-bt soc@03000000:bt: clk not config [ 0.873731] [LCD_FB] lcd_fb_gpio_set_value,line:353: [ 0.873731] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL [ 0.886538] sunxi-wlan soc@03000000:wlan: wlan_busnum (1) [ 0.892625] sunxi-wlan soc@03000000:wlan: wlan_power_num (-1) [ 0.899097] sunxi-wlan soc@03000000:wlan: Missing wlan_io_regulator. [ 0.906236] sunxi-wlan soc@03000000:wlan: io_regulator_name ((null)) [ 0.913388] sunxi-wlan soc@03000000:wlan: request pincrtl handle for device [soc@03000000:wlan] failed [ 0.923893] sunxi-wlan soc@03000000:wlan: wlan_regon gpio=384 mul-sel=1 pull=-1 drv_level=-1 data=0 [ 0.934471] sunxi-wlan soc@03000000:wlan: get gpio chip_en failed [ 0.941336] sunxi-wlan soc@03000000:wlan: wlan_hostwake gpio=388 mul-sel=6 pull=-1 drv_level=-1 data=0 [ 0.952269] sunxi-wlan soc@03000000:wlan: clk_name () [ 0.958752] mtd device must be supplied (device name is empty) [ 0.965667] libphy: Fixed MDIO Bus: probed [ 0.971353] gmac-power0: NULL [ 0.974708] gmac-power1: NULL [ 0.978068] [LCD_FB] lcd_fb_gpio_set_value,line:353: [ 0.978068] OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL [ 0.989526] gmac-power2: NULL [ 0.993839] Failed to alloc md5 [ 0.997373] eth0: Use random mac address [ 1.001989] RTW: module init start [ 1.005833] RTW: rtl8723ds v5.10.1-26-ga10bc0b8b.20200617_COEX20200103-3535 [ 1.013660] RTW: build time: Jul 20 2021 13:31:31 [ 1.018951] RTW: rtl8723ds BT-Coex version = COEX20200103-3535 [ 1.135530] sunxi-wlan soc@03000000:wlan: bus_index: 1 [ 1.141305] sunxi_hosts[1] should not be nullRTW: module init ret=0 [ 1.148471] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.156043] get ehci0-controller, regulator_io is no nocare [ 1.162317] get ehci0-controller wakeup-source is fail. [ 1.168355] sunxi ehci0-controller don't init wakeup source [ 1.174632] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffff8008aebda8, 0x:ffffff8008074000, irq_no:f9 [ 1.188206] [sunxi-ehci0]: Not init ehci0 [ 1.193035] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.200231] get ohci0-controller, regulator_io is no nocare [ 1.206504] get ohci0-controller wakeup-source is fail. [ 1.212522] sunxi ohci0-controller don't init wakeup source [ 1.219033] [sunxi-ohci0]: probe, pdev->name: 4101000.ohci0-controller, sunxi_ohci: 0xffffff8008aec118 [ 1.229519] [sunxi-ohci0]: Not init ohci0 [ 1.234290] get ohci1-controller, regulator_io is no nocare [ 1.240584] get ohci1-controller wakeup-source is fail. [ 1.246774] sunxi ohci1-controller don't init wakeup source [ 1.253186] [sunxi-ohci1]: probe, pdev->name: 4201000.ohci1-controller, sunxi_ohci: 0xffffff8008aec7f8 [ 1.263666] 4201000.ohci1-controller supply drvvbus not found, using dummy regulator [ 1.274527] sunxi-ohci 4201000.ohci1-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 1.284329] sunxi-ohci 4201000.ohci1-controller: new USB bus registered, assigned bus number 1 [ 1.294125] sunxi-ohci 4201000.ohci1-controller: irq 252, io mem 0x00000040 [ 1.365907] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.373547] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.381664] usb usb1: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 1.389684] usb usb1: Manufacturer: Linux 4.9.191 ohci_hcd [ 1.395851] usb usb1: SerialNumber: sunxi-ohci [ 1.401675] hub 1-0:1.0: USB hub found [ 1.405940] hub 1-0:1.0: 1 port detected [ 1.411126] usbcore: registered new interface driver uas [ 1.417211] usbcore: registered new interface driver usb-storage [ 1.424033] usbcore: registered new interface driver ums-alauda [ 1.430743] usbcore: registered new interface driver ums-cypress [ 1.437547] usbcore: registered new interface driver ums-datafab [ 1.444349] usbcore: registered new interface driver ums_eneub6250 [ 1.451349] usbcore: registered new interface driver ums-freecom [ 1.458148] usbcore: registered new interface driver ums-isd200 [ 1.464855] usbcore: registered new interface driver ums-jumpshot [ 1.471751] usbcore: registered new interface driver ums-karma [ 1.478361] usbcore: registered new interface driver ums-onetouch [ 1.485284] usbcore: registered new interface driver ums-realtek [ 1.492092] usbcore: registered new interface driver ums-sddr09 [ 1.498796] usbcore: registered new interface driver ums-sddr55 [ 1.505504] usbcore: registered new interface driver ums-usbat [ 1.512155] usb_serial_number:20080411 [ 1.517481] sunxi_gpadc_init,1891, success [ 1.523065] sunxi-rtc rtc: rtc core: registered sunxi-rtc as rtc0 [ 1.529992] sunxi-rtc rtc: RTC enabled [ 1.534536] i2c /dev entries driver [ 1.538993] lirc_dev: IR Remote Control driver registered, major 249 [ 1.546156] IR NEC protocol handler initialized [ 1.551250] IR RC5(x/sz) protocol handler initialized [ 1.556932] IR LIRC bridge handler initialized [ 1.562092] sun50iw11p1-r-pinctrl r_pio: expect_func as:s_cir0, but muxsel(2) is func:s_ir [ 1.571662] sunxi_ir_startup: get ir protocol failed [ 1.577062] s_cir_rx supply ir0 not found, using dummy regulator [ 1.584159] Registered IR keymap rc_map_sunxi [ 1.589397] input: sunxi-ir as /devices/platform/soc/s_cir_rx/rc/rc0/input1 [ 1.597429] rc rc0: sunxi-ir as /devices/platform/soc/s_cir_rx/rc/rc0 [ 1.605039] rc rc0: lirc_dev: driver ir-lirc-codec (sunxi-rc-recv) registered at minor = 0 [ 1.614949] sun50iw11p1-pinctrl pio: expect_func as:ir0, but muxsel(2) is func:ir [ 1.623495] sunxi_ir_tx_probe()644 - sunxi-ir-tx v1.0.0 [ 1.629404] sunxi_ir_tx_startup()617 - base: ffffff8008b57000 ! [ 1.636162] sunxi_ir_tx_startup()624 - irq num: 245 ! [ 1.641929] Registered IR keymap rc_map_sunxi [ 1.647177] input: sunxi-ir-tx as /devices/platform/soc/ir_tx/rc/rc1/ir_tx [ 1.655113] rc rc1: sunxi-ir-tx as /devices/platform/soc/ir_tx/rc/rc1 [ 1.662622] rc rc1: lirc_dev: driver ir-lirc-codec (sunxi-ir-tx) registered at minor = 1 [ 1.671732] sunxi_ir_tx_probe()695 - register rc device success [ 1.678397] ir_tx_clk_cfg()336 - get ir parent rate 24000000HZ [ 1.684974] ir_tx_clk_cfg()345 - get ir_clk rate 12000000HZ [ 1.691247] sunxi_ir_tx_probe()705 - ir_tx_setup success [ 1.697275] sunxi_ir_tx_probe()715 - request irq success [ 1.703249] sunxi_ir_tx_probe()716 - probe success [ 1.709108] usbcore: registered new interface driver uvcvideo [ 1.715577] USB Video Class driver (1.1.1) [ 1.720182] gspca_main: v2.14.0 registered [ 1.724795] sunxi cedar version 0.1 [ 1.729041] google_vp9: sunxi google vp9 version 0.1 [ 1.736530] sunxi-wdt 20000a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.745667] Bluetooth: HCI UART driver ver 2.2.d448471.20181218-163903 [ 1.753021] Bluetooth: HCI UART protocol H4 registered [ 1.758793] Bluetooth: HCI H4 protocol initialized [ 1.764181] Bluetooth: HCI UART protocol (null) registered [ 1.770353] Bluetooth: HCI Realtek H5 protocol initialized [ 1.776703] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 01.00.07 [ 1.784165] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1 [ 1.790567] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 0 [ 1.797135] [XR_BT_LPM] bluesleep_probe: uart_index(1) [ 1.803092] bt_fdi debugfs_init [ 1.809024] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v3.50 2021-01-04 19:06) [ 1.818094] sunxi-mmc sdc0: ***ctl-spec-caps*** 8 [ 1.823437] sunxi-mmc sdc0: No vmmc regulator found [ 1.828928] sunxi-mmc sdc0: No vqmmc regulator found [ 1.834513] sunxi-mmc sdc0: No vdmmc regulator found [ 1.840097] sunxi-mmc sdc0: No vd33sw regulator found [ 1.845773] sunxi-mmc sdc0: No vd18sw regulator found [ 1.851463] sunxi-mmc sdc0: No vq33sw regulator found [ 1.857142] sunxi-mmc sdc0: No vq18sw regulator found [ 1.863411] sunxi-mmc sdc0: set host busy [ 1.868008] sunxi-mmc sdc0: Got CD GPIO [ 1.872629] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.882974] sunxi-mmc sdc0: no vqmmc,Check if there is regulator [ 1.909733] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.938265] sunxi-mmc sdc0: detmode:gpio irq [ 1.938298] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.945277] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.968192] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.979077] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v3.50 2021-01-04 19:06) [ 1.979264] sunxi-mmc sdc1: No vmmc regulator found [ 1.979269] sunxi-mmc sdc1: No vqmmc regulator found [ 1.979274] sunxi-mmc sdc1: No vdmmc regulator found [ 1.979278] sunxi-mmc sdc1: No vd33sw regulator found [ 1.979283] sunxi-mmc sdc1: No vd18sw regulator found [ 1.979287] sunxi-mmc sdc1: No vq33sw regulator found [ 1.979292] sunxi-mmc sdc1: No vq18sw regulator found [ 1.988684] sunxi-mmc sdc1: set host busy [ 1.988766] mmc:failed to get gpios [ 1.989002] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.989028] sunxi-mmc sdc1: no vqmmc,Check if there is regulator [ 2.005745] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.029739] sunxi-mmc sdc1: detmode:manually by software [ 2.030653] sunxi_led_probe()1690 - start [ 2.030679] sunxi_get_str_of_property()1549 - failed to get the string of propname led_regulator! [ 2.031903] sunxi_led_probe()1782 - finish [ 2.032193] hidraw: raw HID events driver (C) Jiri Kosina [ 2.032355] usbcore: registered new interface driver usbhid [ 2.032357] usbhid: USB HID core driver [ 2.035445] sunxi-daudio daudio1: regulator missing or invalid [ 2.035722] sunxi-daudio daudio2: regulator missing or invalid [ 2.036246] rpmsg_hifi 3003000.msgbox0.sunxi,dsp0.0.-1: id:sunxi,dsp0 new channel: 0x0 -> 0xffffffff! [ 2.037254] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.041087] rpmsg_hifi 3003000.msgbox0.sunxi,dsp0.0.-1: rpmsg hifi[0] client driver is probed [ 2.041191] rpmsg_hifi 3008000.msgbox1.sunxi,dsp1.0.-1: id:sunxi,dsp1 new channel: 0x0 -> 0xffffffff! [ 2.047694] rpmsg_hifi 3008000.msgbox1.sunxi,dsp1.0.-1: rpmsg hifi[1] client driver is probed [ 2.049936] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.054399] sunxi-mmc sdc1: smc 1 p1 err, cmd 8, RTO !! [ 2.065220] sunxi-mmc sdc1: card claims to support voltages below defined range [ 2.065400] sunxi-internal-cpudai cpudai: dmaengine alloc coherent phy_addr:0x4a0a0000 [ 2.065551] sunxi-internal-cpudai cpudai: dmaengine alloc coherent phy_addr:0x4a0c0000 [ 2.065558] sunxi-internal-cpudai cpudai: sunxi_hifi_cpudai_probe start. [ 2.107091] sunxi-internal-cpudai cpudai: sunxi_hifi_cpudai_probe stop. [ 2.107100] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_init [ 2.107804] sunxi-codec-machine sndcodec: sunxi-hifi-codec <-> cpudai mapping ok [ 2.109492] sunxi-rpaf-dsp sunxi_rpaf_dsp0: register device finished! [ 2.109498] sunxi-rpaf-dsp sunxi_rpaf_dsp0: [rpaf_dsp0] probe finished! [ 2.109762] sunxi-rpaf-dsp sunxi_rpaf_dsp1: register device finished! [ 2.109768] sunxi-rpaf-dsp sunxi_rpaf_dsp1: [rpaf_dsp1] probe finished! [ 2.110137] Netfilter messages via NETLINK v0.30. [ 2.110380] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 2.110523] ctnetlink v0.93: registering with nfnetlink. [ 2.113981] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.121505] NET: Registered protocol family 10 [ 2.126825] NET: Registered protocol family 17 [ 2.127215] Bluetooth: RFCOMM TTY layer initialized [ 2.127229] Bluetooth: RFCOMM socket layer initialized [ 2.127250] Bluetooth: RFCOMM ver 1.11 [ 2.127261] 8021q: 802.1Q VLAN Support v1.8 [ 2.138865] get usb_detect_mode is fail, 22 [ 2.141996] sunxi-rtc rtc: setting system clock to 1970-01-01 00:10:33 UTC (633) [ 2.143539] snddaudio snddaudio1: codec: snd-soc-dummy, codec_dai: snd-soc-dummy-dai. [ 2.144220] snddaudio snddaudio1: snd-soc-dummy-dai <-> daudio1 mapping ok [ 2.146161] ALSA device list: [ 2.146165] #0: audiocodec [ 2.146168] #1: snddaudio1 [ 2.285955] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.286073] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.297881] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 2.400010] Waiting for root device /dev/mmcblk0p7... [ 2.402188] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.416986] mmc1: new high speed SDIO card at address 0001 [ 2.423700] RTW: == SDIO Card Info == [ 2.427836] RTW: card: ffffffc0088fb800 [ 2.429092] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.430944] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.431056] sunxi-mmc sdc0: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 2.431196] sunxi-mmc sdc0: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 2.431256] mmc0: new high speed SDHC card at address b368 [ 2.436047] mmcblk0: mmc0:b368 NCard 29.1 GiB [ 2.445202] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 2.489753] RTW: clock: 50000000 Hz [ 2.493869] RTW: timing spec: sd high-speed [ 2.498783] RTW: sd3_bus_mode: FALSE [ 2.502997] RTW: func num: 1 [ 2.506437] RTW: func1: ffffffc008b5cc00 (*) [ 2.511434] RTW: ================ [ 2.517910] random: fast init done [ 2.544440] RTW: HW EFUSE [ 2.547404] RTW: 0x000: 29 81 00 7C E1 88 07 00 A0 04 EC 35 12 C0 A3 D8 [ 2.555456] RTW: 0x010: 21 21 21 21 21 21 23 23 23 23 23 01 FF FF FF FF [ 2.563513] RTW: 0x020: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.571568] RTW: 0x030: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.579619] RTW: 0x040: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.587669] RTW: 0x050: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.595724] RTW: 0x060: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.603776] RTW: 0x070: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.611830] RTW: 0x080: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.619877] RTW: 0x090: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.627924] RTW: 0x0A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.635975] RTW: 0x0B0: FF FF FF FF FF FF FF FF 20 2F 1F 00 00 00 FF FF [ 2.644039] RTW: 0x0C0: FF 29 20 11 00 00 00 FF 00 FF 11 FF FF FF FF FF [ 2.652095] RTW: 0x0D0: 3E 10 01 12 23 FF FF FF 20 04 4C 02 23 D7 21 02 [ 2.660151] RTW: 0x0E0: 0C 00 22 04 00 08 00 32 FF 21 02 0C 00 22 2A 01 [ 2.668205] RTW: 0x0F0: 01 00 00 00 00 00 00 00 00 00 00 00 02 00 FF FF [ 2.676263] RTW: 0x100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.684308] RTW: 0x110: 00 EB 00 6E 01 00 00 00 00 FF 38 01 46 2E 77 E4 [ 2.692361] RTW: 0x120: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.700395] RTW: 0x130: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.708455] RTW: 0x140: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.716507] RTW: 0x150: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.724566] RTW: 0x160: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.732623] RTW: 0x170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.740681] RTW: 0x180: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.748736] RTW: 0x190: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.756778] RTW: 0x1A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.764835] RTW: 0x1B0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.772889] RTW: 0x1C0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.780932] RTW: 0x1D0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.788980] RTW: 0x1E0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.797037] RTW: 0x1F0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF [ 2.805439] RTW: hal_com_config_channel_plan chplan:0x20 [ 3.033948] RTW: [RF_PATH] ver_id.RF_TYPE:RF_1T1R [ 3.039242] RTW: [RF_PATH] HALSPEC's rf_reg_trx_path_bmp:0x11, rf_reg_path_avail_num:1, max_tx_cnt:1 [ 3.049501] RTW: [RF_PATH] PG's trx_path_bmp:0x00, max_tx_cnt:0 [ 3.056154] RTW: [RF_PATH] Registry's trx_path_bmp:0x00, tx_path_lmt:0, rx_path_lmt:0 [ 3.064948] RTW: [RF_PATH] HALDATA's trx_path_bmp:0x11, max_tx_cnt:1 [ 3.072088] RTW: [RF_PATH] HALDATA's rf_type:RF_1T1R, NumTotalRFPath:1 [ 3.079421] RTW: [TRX_Nss] HALSPEC - tx_nss:1, rx_nss:1 [ 3.085288] RTW: [TRX_Nss] Registry - tx_nss:0, rx_nss:0 [ 3.091256] RTW: [TRX_Nss] HALDATA - tx_nss:1, rx_nss:1 [ 3.098232] RTW: rtw_regsty_chk_target_tx_power_valid return _FALSE for band:0, path:0, rs:0, t:-1 [ 3.109856] RTW: rtw_ndev_init(wlan0) if1 mac_addr=38:01:46:2e:77:e4 [ 3.118908] RTW: rtw_ndev_init(wlan1) if2 mac_addr=3a:01:46:2e:77:e4 [ 3.177430] mmcblk0: r/w command failed, status = 0x80000900 [ 3.183834] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 3.196166] sunxi-mmc sdc0: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.206480] sunxi-mmc sdc0: no vqmmc,Check if there is regulator [ 3.229779] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.257776] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.271024] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.305614] sunxi-mmc sdc0: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.316330] sunxi-mmc sdc0: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.327275] sunxi-mmc sdc0: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 3.339038] EXT4-fs (mmcblk0p7): couldn't mount as ext3 due to feature incompatibilities [ 3.349289] EXT4-fs (mmcblk0p7): couldn't mount as ext2 due to feature incompatibilities [ 3.364812] EXT4-fs (mmcblk0p7): mounted filesystem without journal. Opts: (null) [ 3.373287] VFS: Mounted root (ext4 filesystem) readonly on device 179:7. [ 3.382004] devtmpfs: mounted [ 3.385684] Freeing unused kernel memory: 448K [ 3.560333] init: Console is alive [ 3.564407] init: - watchdog - [ 3.567944] init: - preinit - [ 3.864364] random: procd: uninitialized urandom read (4 bytes read) [ 3.903251] mount_root: mounting /dev/root [ 3.908420] EXT4-fs (mmcblk0p7): re-mounted. Opts: (null) [ 3.914661] mount_root: loading kmods from internal overlay [ 4.002520] block: attempting to load /etc/config/fstab [ 4.010822] block: extroot: device not present, retrying in 5 seconds [ 4.181953] [ 4.181953] insmod_host_driver [ 4.181953] [ 4.188742] [ehci0-controller]: sunxi_usb_enable_ehci [ 4.194424] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffff8008aebda8, 0x:ffffff8008074000, irq_no:f9 [ 4.208021] 4101000.ehci0-controller supply drvvbus not found, using dummy regulator [ 4.216844] sunxi-ehci 4101000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.227032] sunxi-ehci 4101000.ehci0-controller: new USB bus registered, assigned bus number 2 [ 4.237304] sunxi-ehci 4101000.ehci0-controller: irq 249, io mem 0xffffff80080873fc [ 4.261908] sunxi-ehci 4101000.ehci0-controller: USB 0.0 started, EHCI 1.00 [ 4.269757] sunxi-ehci 4101000.ehci0-controller: ehci_irq: highspeed device connect [ 4.278543] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.286177] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.294293] usb usb2: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.302700] usb usb2: Manufacturer: Linux 4.9.191 ehci_hcd [ 4.308866] usb usb2: SerialNumber: sunxi-ehci [ 4.314784] hub 2-0:1.0: USB hub found [ 4.319056] hub 2-0:1.0: 1 port detected [ 4.323888] [ohci0-controller]: sunxi_usb_enable_ohci [ 4.329570] [sunxi-ohci0]: probe, pdev->name: 4101000.ohci0-controller, sunxi_ohci: 0xffffff8008aec118 [ 4.340050] 4101000.ohci0-controller supply drvvbus not found, using dummy regulator [ 4.348856] sunxi-ohci 4101000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 4.358657] sunxi-ohci 4101000.ohci0-controller: new USB bus registered, assigned bus number 3 [ 4.368405] sunxi-ohci 4101000.ohci0-controller: irq 250, io mem 0xffffff8008153678 [ 4.437963] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.445602] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.453722] usb usb3: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 4.461738] usb usb3: Manufacturer: Linux 4.9.191 ohci_hcd [ 4.467907] usb usb3: SerialNumber: sunxi-ohci [ 4.473943] hub 3-0:1.0: USB hub found [ 4.478213] hub 3-0:1.0: 1 port detected [ 4.649909] usb 2-1: new high-speed USB device number 2 using sunxi-ehci [ 4.830994] usb 2-1: New USB device found, idVendor=0c45, idProduct=6366 [ 4.838574] usb 2-1: New USB device strings: Mfr=2, Product=1, SerialNumber=3 [ 4.846598] usb 2-1: Product: USB 2.0 Camera [ 4.851408] usb 2-1: Manufacturer: Sonix Technology Co., Ltd. [ 4.857871] usb 2-1: SerialNumber: SN0001 [ 4.864445] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (0c45:6366) [ 4.881127] input: USB 2.0 Camera as /devices/platform/soc/4101000.ehci0-controller/usb2/2-1/2-1:1.0/input/input3 [ 9.055791] block: extroot: cannot find device UDISK [ 9.068450] procd: - early - [ 9.071821] procd: - watchdog - [ 9.106447] random: procd: uninitialized urandom read (4 bytes read) [ 9.214629] procd: - watchdog - [ 9.218517] procd: - ubus - [ 9.220626] random: jshn: uninitialized urandom read (4 bytes read) [ 9.229435] procd (1): /proc/1167/oom_adj is deprecated, please use /proc/1167/oom_score_adj instead. [ 9.248333] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.288663] procd: - init - Please press Enter to activate this console. [ 9.703945] file system registered [ 9.729204] configfs-gadget 4100000.udc-controller: failed to start g1: -19 [ 9.766501] fuse init (API version 7.26) [ 9.778030] read descriptors [ 9.781275] read strings [ 9.826298] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 9.832458] Bluetooth: BNEP filters: protocol multicast [ 9.838404] Bluetooth: BNEP socket layer initialized [ 9.878669] usbcore: registered new interface driver btusb [ 9.919546] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 9.926435] Bluetooth: HIDP socket layer initialized [ 10.064441] xt_time: kernel timezone is -0000 [ 10.290631] EXT4-fs (mmcblk0p7): warning: mounting unchecked fs, running e2fsck is recommended [ 10.305346] EXT4-fs (mmcblk0p7): re-mounted. Opts: (null) [ 10.458532] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 10.493640] random: crng init done [ 10.497465] random: 6 urandom warning(s) missed due to ratelimiting [ 10.793174] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_startup [ 10.800814] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_hw_params [ 10.809090] sunxi-internal-cpudai cpudai: ======== hw_params ======== [ 10.816414] sunxi-internal-cpudai cpudai: pcm_params->format:2 [ 10.823052] sunxi-internal-cpudai cpudai: pcm_params->channels:2 [ 10.829873] sunxi-internal-cpudai cpudai: pcm_params->rate:48000 [ 10.849838] sunxi-internal-cpudai cpudai: pcm_params->period_size:1024 [ 10.849845] sunxi-internal-cpudai cpudai: pcm_params->periods:4 [ 10.849850] sunxi-internal-cpudai cpudai: pcm_params->pcm_frames:1024 [ 10.849856] sunxi-internal-cpudai cpudai: pcm_params->buffer_size:4096 [ 10.849861] sunxi-internal-cpudai cpudai: =========================== [ 10.936484] RTW: txpath=0x1, rxpath=0x1 [ 10.936488] RTW: txpath_1ss:0x1, num:1 [ 11.002162] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 11.004085] sunxi-internal-cpudai cpudai: sunxi_hifi_pcm_hw_params [ 14.065154] sunxi-internal-cpudai cpudai: sunxi_hifi_pcm_hw_free [ 14.224150] sunxi-codec-machine sndcodec: sunxi_hifi_sndcodec_shutdownBusyBox v1.27.2 () built-in shell (ash)_ .-') ('-. ) (`-. ( '.( OO )_ ( OO ).-. ( OO ). ,--. ,--.) / . --. / ,-.-')(_/. \_)-. | `.' | | \-. \ | |OO)\ `.' / | |.-'-' | | | | \ \ /\ | |'.'| | \| |_.' | | |(_/ \ \ | | | | | | .-. | ,| |_.' .' \_) | | | | | | | |(_| | / .'. \ `--' `--' `--' `--' `--' '--' '--' __ _ / / (_)__ __ ____ __ ------------------------/ /__/ / _ \/ // /\ \ / sipeed.com (Neptune) /____/_/_//_/\_,_//_\_\ ------------------------root@TinaLinux:/# uname -a Linux TinaLinux 4.9.191 #28 SMP PREEMPT Tue Jul 20 13:31:53 UTC 2021 aarch64 GNU/Linux root@TinaLinux:/#相關閱讀：
-
R329教程一|周易 AIPU 部署及仿真教程
-
R329開發板產品介紹
總結
以上是生活随笔為你收集整理的R329开发板系列教程之二|实机运行aipu程序的全部內容，希望文章能夠幫你解決所遇到的問題。
- 上一篇： 云计算的虚拟化
- 下一篇： MindManager22直装版思维导图