linux查看端口pvid,交换机端口及常见问题定位(二)
Agenda
1,常用線纜及收發器
2,交換機端口類型
3,常用命令
4,常用診斷工具
5,光口不能UP故障
6,電口為半雙工故障
7,端口UP/DOWN故障
8,端口err-disable故障
9,網絡排障方法總結
10,Console Port介紹
11,Lenovo TOR 交換機家族
端口類型:
Cisco 交換機
對 Cisco 設備來說,交換機的端口分三種: access、 trunk、三層口(no switchport)
華為交換機
對華為交換機來說,交換機的端口分為 :access、 trunk、 hybrid(雜合端口)
Lenovo ToR交換機
對BNT交換機來說,交換機的端口分為:untagging 和 tagging 端口
access 端口:
1,一個 access 端口只能屬于一個 VLAN,它只能轉發這個 VLAN 的數據,它是一個端口最后的歸宿,
即它不能和所連的端口靜態或動態地形成 trunk,那么它就回歸為 access
2,Cisco 交換機的端口缺省為 dynamic desirable,或 dynamic auto
3,dynamic desirable:動態可取模式,主動對端協商,也就是通常的Trunk模式優先。在可以和對端
協商成trunk模式時使用trunk模式,不行則改為access模式
4,華為交換機的access 端口等同于Cisco的access 端口
trunk 端口:
1,當一個端口要轉發多個 VLAN 的流量,那么這個端口要屬于多個 VLAN,對 Cisco 的設備來說,這個
端口的類型要設置為 trunk,也就是當一個端口屬于 trunk 類型,那么它屬于任何 VLAN
2,對于華為的設備來說, 等同 Cisco 的 trunk。 不同的是缺省情況下,華為的 trunk 只屬于
VLAN 1,要想屬于哪些 VLAN,要手工加入
untagging 端口:
相同于 Cisco 交換機的 access 口,是端口的缺省模式
tagging 端口:
1,相當于 Cisco 交換機的 trunk 口,不同的是,缺省情況下, trunk 口屬于所有的 VLAN,
tagging 口可以屬于多個或所有 VLAN,但要手工加入
2,對于刀片交換機,外部端口缺省為 untagging 端口,內部端口缺省為 tagging 端口
hybrid 端口:
華為交換機的特殊端口類型,介于 access 和 trunk 之間即雜合模式,象 trunk 一樣可以讓多個
VLAN 通過,但又不象 trunk 那樣,除了 PVID 的幀外,把其它所有的 VLAN 都要打上 TAG 發去,
hybrid 端口可對這些非PVID VLAN 打 TAG 或不打 TAG
三層口:
交換機的端口既有三層路由功能,也具有二層交換功能。三層交換機端口默認為二層口,如果需要啟用
三層功能就需要在此端口輸入no switchport命令
常用命令:
show running-config 與 show startup-config //對于配置是否被修改, 或者判斷交換機是否運行
正確的配置很有幫助
show logging reverse命令
Mar 5 0:59:04 0.0.0.0 ALERT stg: STG 1, topology change detected
Mar 5 0:59:04 0.0.0.0 ALERT stg: STG 1, new root bridge
Mar 5 0:59:03 0.0.0.0 ALERT system: link up on management port MGT1
Mar 5 0:59:03 0.0.0.0 NOTICE system: SR SFP+ inserted at port EXT1 is Approved
Mar 5 0:59:02 0.0.0.0 NOTICE link: link up on port EXT1
Mar 5 0:59:02 0.0.0.0 NOTICE server: link up on port INTA6
Mar 5 0:59:01 0.0.0.0 NOTICE mgmt: Booting up with compatibility mode.
Mar 5 0:59:01 0.0.0.0 INFO system: booted version 7.8.6 from FLASH image1, active configuration
Mar 5 0:58:52 0.0.0.0 ERROR cfg: Error: CEE is not enabled. Please enable CEE (cee ena) prior toconfiguring the port(s) as Fibre Channel port(s).
Mar 5 0:58:51 0.0.0.0 NOTICE Norm: Init normalization done.
Mar 5 0:58:40 0.0.0.0 NOTICE mgmt: CME A DOWN and CME B UP because Management Module 1 is active
Mar 5 0:58:38 0.0.0.0 NOTICE system: rebooted (power cycle)
show interface命令
Router(config)#show interface link
Alias Port Speed Duplex Flow Ctrl Link Description
------- ---- ----- -------- ------------TX-----RX-- ------ -------------
INTA6 6 10000 full no no up INTA6
INTB6 20 1G/10G full yes yes down INTB6
EXT1 43 10000 full no no up EXT1
EXT2 44 1G/10G full no no down EXT2
EXT11 53 10000 full no no down EXT11
EXT12 54 10000 full no no down EXT12
EXT13 55 10000 full no no down EXT13
EXT14 56 10000 full no no down EXT14
EXT15 57 Auto full no no down EXT15
EXT16 58 Auto full no no down EXT16
EXT17 59 10000 full no no down EXT17
EXT18 60 10000 full no no down EXT18
EXTM 65 any auto yes yes down EXTM
MGT1 66 1000 full no no up MGT1
show interface命令
Router(config)#show interface port INTA6
Current port INTA6 configuration: enabled, PVID/Native-VLAN 1 //PVID
Description INTA6
ErrDisable recovery enabled
STP: edge, auto link-type, no guard //邊緣端口
The Unicast storm control currently turned off
The Multicast storm control currently turned off
The Broadcast storm control currently turned off
802.1p priority: 0
Bandwidth percentage for unicast traffic: global
DSCP remarking for port: disabled
BPDU guard: disabled //BPDU守護
Flood blocking: disabled
L2 Learning: enabled
ACL Port config is empty //訪問控制列表
UDLD: disabled, mode normal
OAM: disabled, mode active
EVB Profile: 0
Reflective Relay is configured off
VLANs:1 //Native vlan
Current Port INTA6 Gig link configuration:
speed 1000/10000, mode full duplex, fctl both, auto on
//速率,雙工模式,流控制,自協商狀態
display interface
display interface GigabitEthernet1/0/5
GigabitEthernet1/0/5 current state : UP //物理端口狀態: UP or DOWN
Line protocol current state : UP
Description:
Switch Port, PVID : 1, TPID : 8100(Hex), The Maximum Frame
Length is 9216
IP Sending Frames' Format is PKTFMT_ETHNT_2, Hardware address is 0000-0a88-15cd
Last physical up time : -
Last physical down time : 2010-04-15 09:19:17
Current system time: 2010-04-19 13:53:58
Port Mode: COMMON FIBER //FIBER or COPPER
Speed : 1000, Loopback: NONE //速率 環回狀態
Duplex: FULL, Negotiation: ENABLE //雙工狀態 自協商狀態
Mdi : NORMAL
display transceiver verbose
display transceiver interface GigabitEthernet4/0/11 verbose
GigabitEthernet4/0/11 transceiver information:
-------------------------------------------------------------
Common information:
Transceiver Type :1000_BASE_SX_SFP //光模塊類型
Connector Type :LC //接口類型
Wavelength(nm) :850 //光模塊波長
Transfer Distance(m) :500(50um),300(62.5um) //光模塊支持光纖的傳輸距離
Digital Diagnostic Monitoring :YES
Vendor Name :JDSU
Vendor Part Number :PLRXPL-VI-S24-HW
Ordering Name :
-------------------------------------------------------------
Alarm information: //光模塊告警信息
RX loss of signal
RX power low
-------------------------------------------------------------
收集Log: 將打印出來的log保存成txt文件,可使用Putty,SecureCRT或者xShell等
華為交換機:
display logbuffer //打印log
display cur //打印當前配置
思科交換機:
show log //打印log, //收集syslog需配置syslog服務器
show env //硬件日志(風扇,電源,溫度等)
Lenovo ToR交換機:
show logging //打印log
show tech-support //打印當前配置
常用診斷工具
Wireshark抓包分析軟件 (經常與交換機的端口鏡像相結合)
端口鏡像(port-mirror)
1,把一個端口(mirrored-port)的收發數據鏡像到另一個端口(Monitor-port),可選擇單向收或發,
也可選擇雙向收發。
2,當在 trouble-shooting 中,在 Monitor-port 上連接安裝抓包軟件的主機,由此可抓到某個
交換機端口的收發包情況及具體包中的數據,以做進一步深入的分析。
Linux tcpdump
PING 回應: 成功與失敗
PING 包根本沒有發出去 or 被目的主機拒絕
PING 包發出去了,到達中間路由器,但目的主機不可達
PING 包發出去了, 被中間的路由器所阻擋(由被 ACL 所deny)
包被目的主機收到,但目的主機拒絕了 PING ,當目的主機能夠發 ICMP 拒絕信息時 (如 Linux 服務
器上設置: #iptables –I INPUT –p icmp –j REJECT)
總結
以上是生活随笔為你收集整理的linux查看端口pvid,交换机端口及常见问题定位(二)的全部內容,希望文章能夠幫你解決所遇到的問題。
- 上一篇: 恶意文件分类
- 下一篇: kass中lisp文件_自动加载文件目录