DNC-cs6200 ospfv3

• SW-1 配置：
• • SW-2 配置：
  • • SW-1 show ipv6 route :
    • SW-2 show ipv6 route :
    • • 備注：

SW-1 配置：

CS6200-28X-EI>enable 
CS6200-28X-EI#config terminal 
CS6200-28X-EI(config)#hostname SW-1SW-1(config)#ipv6 enable //開啟ipv6轉發協議SW-1(config)#router ipv6 ospf  //配置路由ID
SW-1(config-router)#router-id 1.1.1.1
sW-1(config-router)#exit SW-1(config)#vlan 10,20 //創建vlanSW-1(config)#interface vlan 10
SW-1(config-if-vlan10)#ipv6 address 2022:10:10::1/64 
SW-1(config-if-vlan10)#ipv6 router ospf area 0 //配置vlan10 ospfv3 ，區域號為0
SW-1(config-if-vlan10)#no ipv6 nd suppress-ra //開啟IPv6路由器通告
SW-1(config-if-vlan10)#no shutdown 
SW-1(config-if-vlan10)#exit SW-1(config)#interface vlan 20
SW-1(config-if-vlan20)#ipv6 address 2022:20:10::1/64
SW-1(config-if-vlan20)#ipv6 router ospf area 1  //配置vlan20 ospfv3，區域號為1
SW-1(config-if-vlan20)#no shutdown 
SW-1(config-if-vlan20)#exit SW-1(config)#interface ethernet 1/0/1
SW-1(config-if-ethernet1/0/1)#switchport mode access 
SW-1(config-if-ethernet1/0/1)#switchport access vlan 10
SW-1(config-if-ethernet1/0/1)#no shutdown 
SW-1(config-if-ethernet1/0/1)#exit 
SW-1(config)#interface ethernet 1/0/2             
SW-1(config-if-ethernet1/0/2)#switchport mode access   
SW-1(config-if-ethernet1/0/2)#switchport access vlan 20
SW-1(config-if-ethernet1/0/2)#no shutdown 
SW-1(config-if-ethernet1/0/2)#exit 

SW-2 配置：

CS6200-28X-EI>enable 
CS6200-28X-EI#config terminal 
CS6200-28X-EI(config)#hostname SW-2SW-2(config)#ipv6 enable //開啟ipv6轉發協議SW-2(config)#router ipv6 ospf  //配置路由ID
SW-2(config-router)#router-id 1.1.1.2
sW-2(config-router)#exit SW-2(config)#vlan 10,30 //創建vlanSW-2(config)#interface vlan 10
SW-2(config-if-vlan10)#ipv6 address 2022:10:10::254/64 
SW-2(config-if-vlan10)#ipv6 router ospf area 0 //配置vlan10 ospfv3 ，區域號為0
SW-2(config-if-vlan10)#no ipv6 nd suppress-ra //開啟IPv6路由器通告
SW-2(config-if-vlan10)#no shutdown 
SW-2(config-if-vlan10)#exit SW-2(config)#interface vlan 30
SW-2(config-if-vlan30)#ipv6 address 2022:30:10::1/64
SW-2(config-if-vlan30)#ipv6 router ospf area 2 //配置vlan20 ospfv3，區域號為2
SW-2(config-if-vlan30)#no shutdown 
SW-2(config-if-vlan30)#exit SW-2(config)#interface ethernet 1/0/1
SW-2(config-if-ethernet1/0/1)#switchport mode access 
SW-2(config-if-ethernet1/0/1)#switchport access vlan 10
SW-2(config-if-ethernet1/0/1)#no shutdown 
SW-2(config-if-ethernet1/0/1)#exit 
SW-2(config)#interface ethernet 1/0/2             
SW-2(config-if-ethernet1/0/2)#switchport mode access   
SW-2(config-if-ethernet1/0/2)#switchport access vlan 30
SW-2(config-if-ethernet1/0/2)#no shutdown 
SW-2(config-if-ethernet1/0/2)#exit 

SW-1 show ipv6 route :

IPv6 Routing Table
Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF,I - IS-IS, B - BGP
Timers: UptimeC   ::1/128 via ::, Loopback, 02:55:50  tag:0
C   2002:10:10::/64 via ::, Vlan10, 00:11:26  tag:0
O   2022:10:10::/64 [110/1] via ::, Vlan10, 00:10:35  tag:0
C   2022:20:10::/64 via ::, Vlan20, 00:58:03  tag:0
O   2022:30:10::/64 [110/2] via fe80::203:fff:fe91:d4b8, Vlan10, 00:10:25  tag:0

從show ipv6 route 可看出SW-1通過ospf都學習到了SW-2的接口地址

SW-2 show ipv6 route :

IPv6 Routing Table
Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF,I - IS-IS, B - BGP
Timers: UptimeC   ::1/128 via ::, Loopback, 02:57:30  tag:0
O   2002:10:10::/64 [110/1] via ::, Vlan10, 00:12:13  tag:0
C   2022:10:10::/64 via ::, Vlan10, 00:13:04  tag:0
O   2022:20:10::/64 [110/2] via fe80::203:fff:fe91:d4be, Vlan10, 00:12:13  tag:0
C   2022:30:10::/64 via ::, Vlan20, 00:46:15  tag:0

從show ipv6 route 可看出SW-1通過ospf都學習到了SW-2的接口地址

備注：

no ipv6 nd suppress-ra
ipv6 enable
這兩條命令必須開啟，交換機之間才能學習到對方的路由

總結

以上是生活随笔為你收集整理的DNC-cs6200 ospfv3的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。